Imperial manifold gauge seti All models error codes
Codes
- dAL76Error codeThese alarms are for future expansion, and are not in use at this time
- dAL86Error codeThe real time clock (RTC) backup battery is too low to adequately maintain the RTC reading. A real time clock failure is critical to the operation of the unit. After replac- ing the battery the following actions are required: • Update the RTC setting • Update the unit's software configuration • Update the operational software • Update all user selectable function code settings (defrost, setpoint, etc)
- dAL89Error codeAn error has been detected in the process of writing daily data to the nonvol- atile FLASH memory
- dAL90Error codeThis alarm is for future expansion, and is not in use at this time
- dAL91Error codeThe DataCORDER alarm queue is determined to be full (eight alarms)
- dC1Error codeCurrent reading of the supply recorder sensor
- dC2Error codeCurrent reading of the return recorder sensor
- dC3-5Error codeCurrent readings of the three USDA probes
- dC6-13Error codeCurrent values of the network data points (as configured). Data point 1 (Code 6) is generally the humidity sensor and its value is obtained from the Controller once every minute
- dC14Error codeCurrent reading of the cargo probe #4
- dC20-24Error codeCurrent calibration offset values for each of the five probes: supply, re- turn, USDA #1, #2, and #3. These values are entered via the interroga- tion program
- dC29Error codeNumber of days of data that are currently stored in the DataCORDER
- dC31Error codeShows the current status of the optional battery pack. PASS: Battery pack is fully charged. FAIL: Battery pack voltage is low
- dC32Error codeCurrent time on the real-time clock (RTC) in the DataCORDER
- dC33Error codeCurrent date (month and day) on the RTC in the DataCORDER
- dC34Error codeCurrent year on the RTC in the DataCORDER
- F3Error code
- OFF1Error codeManual Addressing Valve No. 2
- P0-0Error codePreTrip Initiated: Configuration Display, Indicator Lamps, LEDs, and Displays
- P1-0Error codeHeaters On Test
- P1-1Error codeHeaters Off Test
- P2-0Error codeCondenser Fan On Test
- P2-1Error codeCondenser Fan Off Test
- P3-0Error codeLow Speed Evaporator Fans On Test
- P3-1Error codeLow Speed Evaporator Fan Off Test
- P4-0Error codeHigh Speed Evaporator Fan Motors On
- P4-1Error codeHigh Speed Evaporator Fan Motors Off
- P5-0Error codeSupply / Return Probe Test
- P5-1Error codeSupply Probe Test
- P5-2Error codeReturn Probe Test
- P5-10Error codeHumidity Sensor Controller Configuration Verification Test
- P5-11Error codeHumidity Sensor Installation Verification Test
- P5-12Error codeHumidity Sensor Range Check Test
- P6-0Error codeCompressor On
- P6-2Error codeSuction Modulation Valve (Open and Closed)
- P6-3Error codeQuench Valve Test
- P6-5Error codeNot Applicable
- P7-0Error codeHigh Pressure Switch Closed
- P7-1Error codeHigh Pressure Switch Open
- P8-0Error codePerishable Mode Heat Test
- P8-1Error codePerishable Mode Pull Down Test / eAutofresh CO 2 Sensor Calibration
- P8-2Error codePerishable Mode Maintain Temperature Test
- P9-0Error code
- P10-0Error codeFrozen Mode Setup Test
- P10-1Error codeFrozen Mode Pulldown Test
- P10-2Error codeFrozen Mode Maintain Temperature Test
- SW01MError codeNo. 1 No. 2 No. 3 No. 4