Markasi-Belli-Degil All models error codes
Codes
- F2Error codeMakine atık suları boşaltamıyor.
- F2-05Error codeFull beam light right.
- F3Error codeSürekli su alma hatası
- F3-05Error codeDipped beam light right.
- F4Error codeWasher controller Check VFD fault code before turning off power. Try the
- F4-05Error codeDipped beam light left / Supp. sw. fog light rear.
- F16-02Error codeECU YTxx3 CC2 (KL30AR).
- F17Error codeRelay(s) Welded Manual The AC1 L1 transfer relay Disconnect the inverter’s
- F17-02Error codeECU YTxx3 CC2 (KL30AR).
- F18Error codeRelay(s) Welded Manual AC1 L2 transfer relay is See F17.
- F18-15Error codeECU YTxx3 CC2 (KL30AR).
- F19Error codeRelay(s) Welded Manual AC2 L1 transfer relay is See F17.
- F19-10Error codeDisplay (KL30AR).
- F20Error codeRelay(s) Welded Manual AC2 L2 transfer relay is See F17.
- F21Error codeRelay(s) Welded Manual An unidentified transfer See F17.
- F22Error codeRelay(s) Welded Manual An unidentified L1 See F17.
- F23Error codeAI Over Automatic Over-frequency anti- No action required. The
- F24Error codeAI Under Automatic Under-frequency anti- See F23.
- F25Error codeAI Over Automatic Over-frequency anti- See F23.
- F26Error codeAI Under Automatic Under-frequency anti- See F23.
- F27Error codeAI L1 Over Automatic Over-voltage anti- See F23.
- F28Error codeAI L2 Over Automatic See F27. See F23.
- F29Error codeAI L1L2 Over Automatic Over-voltage anti- See F23.
- F30Error codeAI L1L2 Over Automatic Over-voltage anti- See F23.
- F31Error codeAI L1 Over Automatic Over-voltage anti- See F23.
- F32Error codeAI L2 Over Automatic Over-voltage anti- See F23.
- F33Error codeAI L1L2 Over Automatic Over-voltage anti- See F23.
- F34Error codeAI L1 Under Automatic Under-voltage anti- See F23.
- F35Error codeAI L2 Under Automatic See F34. See F23.
- F36Error codeAI L1L2 Under Automatic See F34. See F23.
- F37Error codeAI L1 Under Automatic Under-voltage anti- See F23.
- F38Error codeAI L2 Under Automatic See F37. See F23.
- F39Error codeAI L1L2 Under Automatic Under-voltage anti- See F23.
- F40Error codeAI L1L2 Under Automatic Under-voltage anti- See F23.
- F41Error codeAPS Under Escalating Auxiliary power supply Clear the fault and attempt
- F42Error codeAPS Over Voltage Escalating Auxiliary power supply Clear the fault and attempt
- F43Error codeCartridge expired. The cartridge needs to be updated. Replace cartridge.
- F44Error codeBattery Over Automatic Battery over- temperature Clear the fault and attempt
- F45Error codeCapacitor Over Automatic Capacitor over- Clear the fault and attempt
- F46Error codeController fault Manual Controller fault Service required.
- F47Error codeDC Under Voltage Automatic DC under-voltage Check for the correct battery
- F48Error codeDC Under Voltage Automatic DC under-voltage See F47.
- F49Error codeDC Over Voltage Escalating DC over-voltage Clear the fault and attempt
- F260Error codeError in the calibration carried Exchanging the electronics Bit 8 of Byte 0 … 5
- F261Error codeError during setup Repeat setup Bit 9 of Byte 0 … 5
- F264Error codeAdjustment not within the vessel Check or correct installation Bit 10 of Byte 0 … 5
- F265Error codeSensor no longer carries out a Check operating voltage Bit 11 of Byte 0 … 5
- F301Error codeTemperature setting request Set point temperature is not set.
- F401Error codeIn the chilled or partial frozen Short circuit or breakage of both sensor lead wires
- F403Error codemode, the supply air sensor Wrong wiring connection on both sensors