Markasi-Belli-Degil All models error codes
Codes
- F5Error codehortumun bağlantı ucundaki filtreyi
- F6Error codeSıcaklık sensörü hatalı Servise başvurunuz.
- F7Error codeMarks or unmarks all tests in all menus.
- F7-10Error codeReversing / Fog Light (KL15).
- F8Error codeIsıtıcı hatası Servise başvurunuz.
- F8-15Error codeTrailer connector (KL15).
- F9Error codeThe washer tub does Check VFD fault code before turning off power.
- F9-15Error codeWiper front (KL15).
- F50Error codeCartridge comm. failed The cartridge is detected, but no Replace cartridge.
- F51Error codeThe dummy cell is not installed. Plug in the dummy cell.
- F52Error codeEEPROM Error Manual No action. Clear fault and
- F53Error codeEEPROM Error Manual See F52.
- F54Error codeEEPROM Error Manual See F52.
- F55Error codeEEPROM Error Manual See F52.
- F56Error codeEEPROM Error Manual See F52.
- F57Error codeFET1 Over Automatic Internal temperature is Fault clears when
- F58Error codeFET2 Over Automatic See F57. See F57.
- F59Error codeGOCFG process Manual Auto-configuration Retry the Copy From?
- F63Error codeAC Overload Escalating Excessive load on the AC Check for loads above the
- F64Error codeAC Overload L1 Escalating Excessive load on the AC See F63
- F65Error codeAC Overload L2 Escalating Excessive load on the AC See F63.
- F66Error codeSystem Automatic Multi-Unit Configuration Ensure only one unit is
- F67Error codeWatchdog Error Manual Service required.
- F68Error codeTransformer Over Automatic The transformer The fault clears when the
- F69Error codeExternal Sync Manual Check connections and
- F70Error code
- F71Error codeToo Many Masters Automatic In a Multi Unit There can only be one Master
- F72Error codeTransmitter supply voltage fail The transmitter is defective.
- F73Error codeTransformer Temp Automatic Temperature Service required.
- F74Error codeOther Unit Automatic In a Multi Unit Clear the primary fault on the
- F75Error codeMaster Inverter Automatic In a Multi Unit Make sure that the two units
- F76Error codeNo Masters Automatic In a Multi Unit Assign the other unit as
- F79Error codeBattery Sensor Automatic The BTS has been Replace the BTS.
- F80Error codeTemperature limits exceeded. Temperature is outside the limits Check the installation environment.
- F81Error codeGas inlet flow rate fail Flow < 70% nominal for 60 seconds.
- F82Error codeRESERVED RESERVED RESERVED
- F83Error codePyrolyzer fail Pyrolyzer fails to heat Check the electrical connection to the Pyrolyzer.
- F84Error codeMisc. transmitter fault. The transmitter is defective. Service or replace Midas S2
- F85Error codePowerBoard Over Automatic Same as F57. Same as F57.
- F86Error codeDead Battery Automatic When only Line 1 is Both Line 1 and Line 2 must
- F87Error codeInconsistent Automatic In a Multi Unit Configure all units to the
- F88Error codeMPPT Ground Automatic In a Xanbus Check the MPPT and clear
- F91Error codePyrolyzer installation fault Pyrolyzer is not installed properly Check gas type or reinstall the Pyrolyzer.
- F92Error codeNP1 pyrolyzer module failure Check flow connections between Midas S2 and NP1 Pyrolyzer.
- F93Error codeWrong Batt Automatic An unknowns BTS Use only the BTS that was
- F500Error codeSilicon Serial ID Manual Silicon Serial ID Failure Service required.
- F603Error codeSuction modulating valve coil is broken.
- F701Error codeAbnormal power voltage Note) 1.
- F705Error codeS phase is open phase The voltage selector is in poor contact.
- F803Error codeAny following malfunction Refer to the possible cause of the left mentioned malfunction codes.