Bmw All models error codes
Codes
- 2AError codeValvetronic valve timing system malfunction - minimum lift limit exceeded
- 2BError codeIncorrect mass air flow. The problem may be the operation of the flow meter sensor or a malfunction of one of the air lines. In rare cases, the cause is a problem with the engine itself
- 2CError codeMalfunctions in the boost pressure control system. The unit has been switched off, engine malfunctions are possible. The pressure build-up is out of range
- 2DError code
- 2EError codeElektrikli su pompası arızası
- 2FError codeİmmobilizer iletişim hatası
- 3Error codeIgnition timing error
- 3EError codeThe automatic transmission sensor is malfunctioning, the connection of the device may be poor. If the sensor and wiring are intact, the engine and transmission control unit is subject to diagnosis. The reason may be a software malfunction
- 3FError codeCharge Air Pressure Controller Malfunction
- 27CError codeMalfunction of the engine fluid level temperature sensor. If the problem is a short circuit, the instrument panel may display information about the overheating of the power unit, although in fact the engine is running normally.
- 28Error codeBreakage of the lambda probe or the absence of a signal emanating from it. If the control unit cannot determine the presence of an oxygen sensor, this may indicate a loss of communication as a result of wiring damage
- 28AError codeIncorrect throttle position angle. The inlet pressure does not correspond to the normalized data
- 28CError codeMalfunction associated with the operation of the glow plug control module. The device does not send a signal to the microprocessor module via the LIN bus
- 28DError codeMalfunctions in the communication system with the generator set. The cause of the problem may be poor contact of the device with the mains or a malfunction of one of the constituent elements of the generator, for example, a voltage regulator relay
- 29Error codeProblems related to the functioning of the speedometer controller. It is possible that the sensor installed on the instrument panel is faulty.
- 29DError codeFuel misfires with reduced fuel volume in the tank.
- 29EError codeError in the formation of the air-fuel mixture.
- 29FError codeLow pressure in the low pressure fuel system
- 30Error code
- 30BError codeMalfunctions in the operation of the high pressure fuel pump or converter elements. The cause of the problem may be due to a malfunction of one of the fuses or relays
- 30FError codeDüşük turbo basıncı tespit edildi
- 32Error codeCÁLUÁTCÁH SÁWITÁCHÁ . Á. . . Á. . . Á. . . Á. . . Á. . . Á. . . .Á
- 33Error codeMalfunction of the transmission torque converter
- 35Error codeDÁRIVÁERÁ’S ÁMAÁKE-ÁUPÁ MIÁRRÁORÁ LIGÁHTÁ . Á
- 36Error codePÁASÁSENÁGEÁR’SÁ MÁAKÁE-UÁP MÁIRÁROÁR LÁIGHÁT ÁÁÁÁÁÁÁÁÁÁÁÁÁ
- 37Error codeCritically high voltage in the mains, which is more than 16 volts. Possible causes of the problem: Bad battery. It is possible that the battery is discharged as a result of the destruction of the plates located inside. Failure of the generator set or poor contact of the device with the network. It is possible that the contact simply disconnected from the device. Damaged or worn drive strap. Use of electrical equipment, the technical parameters of which do not correspond to the characteristics of the electrical network
- 38Error code(Á3 PÁINSÁ, BLÁACÁK) Á. . . Á. . . Á. . . Á. . . Á. . . Á. . . Á. . . .Á . . ÁÁÁÁÁÁÁÁÁÁÁÁÁ
- 39Error codeElectrical error in the servomotors
- 40Error code(Á1 PÁIN, ÁBLAÁCKÁ) . Á. . . Á. . . Á. . . Á. . . Á. . . Á. . . Á. . . .Á
- 41EError code
- 42Error codeMalfunction of the multi-function switch installed on the steering wheel
- 42DError codeCommunication failure with BSD control module - glow plugs. If the block itself is faulty, this will lead to an incorrect start of the engine, in some cases it will not be possible to start it
- 43Error codeMalfunctions or failure of the exhaust gas adjustment potentiometer. This error can only appear in vehicles that are not equipped with a catalytic device
- 281DError codeDisruption of communication with the BSD generator. The signal coming from the device does not correspond to the normalized parameters
- 285AError codeMalfunctions in the variable valve timing system. The problem is a malfunction of the servo control mechanism or directly in the drive device
- 285EError codeEML error (EML) - a malfunction in the valve stroke control system. There may be problems with starting the engine, up to the impossibility of starting it
- 287DError codeThere is no signal from the pressure controller located in the fuel rail.
- 296AError codeMalfunctions of the lambda oxygen sensor or lack of signal from the device located in front of the catalyst device
- 299BError codeNo signal or incorrect pulse coming from the battery sensor. Malfunction of the IBS regulator, the device is located on the negative terminal of the battery. The problem may be a poor connection between the device and the dashboard
- 300Error codeEngine malfunction. The user will have to look for the cause of the problem on their own
- 377AError codeMalfunction of the water pump or pump - the device is blocked.
- 434EError codeMalfunction in the operation of the damper system, activation of the device is disturbed
- 2854Error codeMalfunction in the variable throttle mechanism.
- 2883Error codeIncorrect ratio of the air-fuel mixture, problems in the formation were fixed. Perhaps, as a result of a software malfunction, the device set incorrect parameters for the formation of an air mixture
- 3100Error codeMalfunctions in the boost pressure control system.
- 3234Error codeSUPPLEMENTAL RESTRAINT ÁÁÁÁÁÁÁÁÁÁÁ SYSTEM (AIR BAG) ÁÁÁÁÁÁÁÁÁÁÁ
- 4166Error codeMalfunctions of the soot particle filtration system
- 4200aError codeFalse code that does not indicate a malfunction in the car. The reason is the incorrect functioning of the software of the vehicle control unit or malfunctions in the firmware. Also, the code may be informational in nature and not be related to the operation of the microprocessor
- 4203Error codeThe verbatim interpretation of the error is “the pre-start state of the glow plug”. If the spark plugs are new, the cause may be a malfunction or software failure of the glow plug control unit
- 4205Error codeTransmission related fault. The transmission may go into speed limit mode