Bmw All models error codes
Codes
- 1BError code
- 1dError codeBreakage of the cable supplying the programmable thermostat. The device will not be able to activate at the right time, which will lead to insufficient cooling or overheating of the power unit. Also, the problem may be damage to one of the lines of the cooling system
- 11Error codeThe fuel pressure regulator in the car’s gas tank is out of order, the problem is in the operation of the evaporator system
- 11AError codeIncorrect fuel pressure in the line, fixed by the control unit
- 12Error codeNo signal coming from the vehicle speed sensor
- 14Error codeMalfunctions or no valve relay communication signal
- 15Error codeMalfunctions recorded in the operation of the pressure pumping device of the system
- 16Error codeMalfunctions of the injectors installed in the first and third cylinders. The problem may be due to a malfunction of the electrical circuits
- 17Error codeMalfunctions of the front ABS sensors installed on the left wheel of the car. The cause of the problem may be a lack of contact or damage to the wiring
- 19Error codeMalfunctions in the intake valve activation system
- 21Error codeOÁN-ÁBOÁARÁD CÁOMÁPUÁTERÁ TÁEMÁPERÁATÁURÁE SENSOR . . . . . . . . . . . . . . . . . . . . . . . . . . . . ÁÁÁÁÁÁÁÁÁÁÁÁÁ
- 22Error codeMalfunction of the third, sixth or fourth engine nozzle.
- 25Error codeMalfunction in functioning of switches of stoplights
- 25cError codeMalfunction in the operation of the exhaust gas backpressure controller installed in the exhaust tract
- 27Error codeMalfunction of the idle speed sensor
- 27AError codeMalfunction of the EWS digital interface connected to the DME unit
- 27BError codeMalfunctions in the control function of the camshaft of the exhaust system in the second row. A violation of the identification of labels or valves has been reported
- 100Error codeIn Russian, in BMW X3, X5 4×4, E70 and other models, this combination indicates a malfunction in the operation of the switching device of the ignition system. Often the problem is associated with damage and moisture ingress
- 101Error codeMalfunctions of the power unit, first of all it is recommended to check: Oil level and volume in the engine. If there is not enough lubricant, it is added. In the event that the consumable contains traces of deposits, sediment or wear products, a fluid replacement with a complete drain is required. Motor control unit and its connection. If the wiring is intact, then the cause of the problem may be a software malfunction of the microprocessor. The operation of manifold devices and sensors, including oxygen, mass air flow and lubricant pressure. Alignment of marks on camshafts. The cause of the problem may be the wear of the pulleys and damage to one of the teeth of the device. The integrity of the timing belt.
- 101FError codeIncorrect throttle opening angle pressure.
- 104Error codeAngle Controller Malfunction
- 106Error codeMalfunction or failure of the lateral acceleration controller
- 113Error codeMalfunction of the return pump of the anti-lock brake system
- 115Error codeABS control module internal error
- 123Error codeThermostat failure.
- 149Error codeCAN bus communication error between anti-lock braking system modules and DSC unit
- 151Error codeABS control unit coding error
- 183Error codeInternal malfunction or displacement of the vehicle steering angle controller
- 200Error codeMalfunctions in the operation of the motor control module, the problem may be its poor contact with the mains
- 202Error codeGeneral fault code for the engine control unit. The problem may be a damaged wiring or a software malfunction of the module
- 203Error codeMalfunctions associated with the functioning of the primary ignition power line
- 204Error codeMalfunction of the resistor element of the ignition system
- 206Error codeMechanical malfunction in the operation of the Vanos system of intake valves
- 214Error codeMalfunction in the cruise control system.
- 244cError codeCritically low air pressure. With such a problem, the engine may not accelerate well, and the box often does not go into manual or sport mode (for automatic transmissions). It is recommended to dismantle the turbine and diagnose it, as well as make sure that there are no defects and that the geometry of the unit is correct
- 279CError codeThe thermostat is malfunctioning (device stuck), but this error code may indicate the following problems: Damage to the wiring or poor-quality signal from the device to the control unit. Use of low quality liquid. As a result of the fact that the used consumable cannot perform its functions of cooling the power unit, the microprocessor module regards this as a thermostat malfunction. Clogging of the channels of the cooling system with wear products and antifreeze deposits. Faulty coolant temperature sensor. The problem may appear as a result of a software failure. Mechanical damage to one of the pipes or expansion tank, which led to the leakage of refrigerant from the system
- 1202Error codeExcess boost pressure
- 1203Error codeInsufficient boost pressure The problem manifests itself with the following errors: malfunction of the turbine or blower; reduced pressure of motor fluid in the engine; malfunctions of the EGR system; the appearance of excess air in the intake manifold or the air flow is difficult as a result of filter clogging; failure of the boost pressure controller
- 1204Error codeInsufficient boost pressure. There may be problems with the drive
- 1260Error codeMalfunction in the control system of the fuel supply pumping device. The problem may be the failure of the motor or damage to the connector.
- 1301Error codeGeneral fault code in the operation of the variable valve timing system. The problem may be one of the teeth is worn or damaged
- 1303Error codeMalfunctions in the operation of the variable valve timing system. Malfunction in the operation of the control mechanism, the required position of the shafts has not been reached
- 1387Error codeMalfunctions in the operation of the radiator installation. The problem lies in the incorrect position of the screen of the engine cooling radiator. The device may be clogged or worn out
- 1613Error codeMalfunctions in the smooth idle system. There are possible jumps in revolutions up or down, a decrease in the power of the power unit
- 2139Error codePossible short circuit on the contacts of one of the connectors
- 2715Error codeOn BMW X1 and other versions, this code indicates a lambda controller installed in front of the catalyst.
- 2731Error codeMalfunction in the operation of the intake camshaft control system.
- 2742Error codeMalfunctions in the formation of the air mixture or misfiring in the first cylinder of the engine
- 2781Error codeOften this error occurs in conjunction with a DTC malfunction - Dynamic traction control
- 2782Error codeGeneral error code indicating problems with the exhaust camshaft position sensor