Yaskawa All models error codes
Codes
- E4-05Error codeSets the phase-to-phase resistance of motor 2 in ohms. Automatically during Auto-Tuning
- E4-06Error codeSets the voltage drop due to motor leakage inductance as a percentage of rated voltage of motor 2. Automatically set during Auto-Tuning
- E4-07Error codeSet to the motor iron saturation coefficient at 50% of magnetic flux. Automatically set during Rotational Auto-Tuning
- E4-08Error codeSet to the motor iron saturation coefficient at 75% of magnetic flux. This value is automatically set during Rotational Auto-Tuning
- E4-09Error codeSets the motor mechanical loss as a percentage of motor rated power (kW) capacity. Adjust in the following circumstances: • When there is a large amount of torque loss due to motor bearing friction. • When there is a large amount of torque loss
- E4-10Error codeSets the motor iron loss in watts
- E4-11Error codeSets the motor rated capacity in kW. Automatically set during Auto-Tuning
- E4-12Error codeSet to the motor iron saturation coefficient at 130% of magnetic flux. Automatically set during Rotational Auto-Tuning
- E4-14Error codeSets the slip compensation gain for motor 2. The function is the same as C3-01 for motor 1. Refer to C3-01: Slip Compensation Gain on page 131
- E4-15Error codeSets the torque compensation gain for motor 2. The function is the same as C4-01 for motor 1. Refer to C4-01: Torque Compensation Gain on page 132
- E5Error codePM Motor Settings ...............................................................................................................155
- E5-01Error codeThe maximum output voltage of the drive is determined by its input voltage. Vector control uses voltage to control the currents within the motor. If the vector control voltage reference value exceeds the drive output voltage capability, the speed control accuracy will decrease because the motor curr
- E72Error codeFeedback Option Module Detection Failure
- Eb1Error codeSafety Function Signal Input Timing Error
- een10Error code50 ms
- EFError codeExternal fault
- EF0Error codeBir opsiyon kartı yoluyla üst kontrol birimi tarafından harici bir hata tetiklendi
- EF1Error code• S1 ile S8 dijital giriúlerinden biri yoluyla harici bir devre tarafından bir hata tetiklendi. • Dijital giriúlerin ayarı yanlıútır
- EF2Error codeFault Display
- EF3Error codeProtective Operation. Output is shut OFF and motor coasts to a stop
- EF4Error codeCPF-01 Transmission fault occurred for 5 sec or more when transmission starts with the digital operator
- EF5Error codeExternal Fault (input terminal S5)
- EF6Error codeExternal Fault (input terminal S6)
- EF7Error codeEEPROM Write Error
- EF8Error code• Toprak kaçak akımı, sürücülerin anma çıkıú akımının %50'sini aútı. • Kablo veya motor yalıtımı arızalıdır. • Sürücü çıkıúında aúırı kaçak kapasite var
- En20Error codesure the power supply voltage is correct: 0 V class: single-phase 200 to 240 Vac 50/60 Hz 0 V class: 3-phase 200 to 240 Vac 50/60 Hz 0 V class: 3-phase 380 to 480 Vac 50/60 Hz
- Ens200Error codeure the power supply voltage is correct: V class: single-phase 200 to 240 Vac 50/60 Hz V class: 3-phase 200 to 240 Vac 50/60 Hz V class: 3-phase 380 to 480 Vac 50/60 Hz
- ErError codeEEPROM Okuma Hatası
- Er-01Error codeMotor veri hatası Motor giriú de÷erleri geçerli de÷ildir. (Örn. baz frekansı ve baz hız uymuyor)
- Er-02Error codeKüçük Hata • Ba÷lantı hatalı. • Yük fazla a÷ırdır
- Er-04Error codeDirenç hatası • De÷er yanlıú girilmiú. • Auto tuning verilen zaman dilimini aútı. • Hesaplanan de÷erler aralık dıúındadır
- Er-05Error codeYüksüz Akım Hatası • Do÷ru olmayan de÷er girildi. • Auto tuning fazla uzun sürdü. • Hesaplanan de÷erler aralık dıúındadır
- Er-08Error codeNominal Kayma Hatası • Yanlıú de÷er girildi. • Auto tuning verilen zaman dilimini aútı. • Hesaplanan de÷erler aralık dıúındadır
- Er-09Error codeHızlanma hatası Motor belirlenen hızlanma süresinde hızlanamadı
- Er-12Error codeAkım algılama hatası • Bir veya bütün çıkıú fazları kaybedildi. • Akım ya fazla düúüktür veya sürücünün anma de÷erini aúıyor. • Akım sensörleri hatalıdır
- Er-13Error codeKaçak Endüktans Hatası Sürücü kaçak endüktans için 300 sn içerisinde tuning yapmakta baúarısızdır
- F1Error codeError Detection for V/f Control with PG ................................................................................157
- F1-02Error codeSets stopping method when a PG open circuit fault (PGO) occurs. Refer to parameter F1-14. 0: Ramp to Stop - Decelerate to stop using the active deceleration time. 1: Coast to Stop 2: Fast-stop - Decelerate to stop using the deceleration time in C1-09. 3: Alarm only - Drive continues operation
- F1-03Error codeSets the stopping method when an overspeed (OS) fault occurs. Refer to F1-08 and F1-09. 0: Ramp to stop - Decelerate to stop using the active deceleration time. 1: Coast to stop 2: Fast-stop - Decelerate to stop using the deceleration time in C1-09. 3: Alarm Only - Drive continues operation
- F1-04Error codeSets the stopping method when a speed deviation (DEV) fault occurs. Refer to F1-10 and F1-11. 0: Ramp to stop - Decelerate to stop using the active deceleration time. 1: Coast to stop 2: Fast-stop - Decelerate to stop using the deceleration time in C1-09. 3: Alarm only - Drive continues operation
- F1-08Error codeSets the speed feedback level which has to be exceeded for the time set in F1-09 before an OS fault will occur. Set as a percentage of the maximum output frequency (E1-04)
- F1-09Error codeSets the time in seconds for which the speed feedback has to exceed the overspeed detection level F1-08 before an OS fault will occur
- F1-10Error codeSets the allowable deviation between motor speed and frequency reference before a speed deviation fault (DEv) is triggered. Set as a percentage of the maximum output frequency (E1-04)
- F1-11Error codeSets the time in seconds for which a deviation between motor speed and frequency reference has to exceed the speed deviation detection level F1-10 before a DEV fault will occur
- F1-14Error codeSets the time for which no PG pulses must be detected before a PG Open (PGO) fault is triggered
- F2Error codeyüksek performans özelliklerinden yararlanmak için kullanınız. A1000 Serisi AC Sürücü Hızlı Başlangıç Kılavuzu (bu kitap) Öncelikle bu kılavuzu okuyun. Kılavuz, ürün paketinde bulunur. Sürücünün kurulması ve kablo
- F6Error codeNetwork Communications
- F6-01Error codeSelects the operation after a communications error occurred. 0: Ramp to stop using current accel/decel time 1: Coast to stop 2: Fast-stop using C1-09 3: Alarm only
- F6-02Error codeSets when an external fault from a comm option is detected. 0: Always detected 1: Detection during Run only
- F10Error codeMain Circuit Cable Open Phase(With the main power supply ON, voltage was low for more than 1 second in an R, S, or T phase.)(Detected when the main power supply was turned ON.)