Toper endüstriyel öğütme makinesi All models error codes
Codes
- P0AError codeThe generator/motor controller is good; the generator/motor caused the fault. 1. 2. refer to Connecting and Disconnecting the 48V Battery System, page 7-8. 3. refer to the Service Manual for the machine. 4. Assemble the generator/motor controller to the generator housing with the 2 capscrews, washers, and locknuts. 5. Plug the harness connector for the generator/motor into the harness connector for the generator/motor controller. 6. Assemble the 3 high-current terminals of the generator/motor to busbars of the generator/motor controller with the flange-head capscrews. Torque the capscrews to 8 to 9 N∙m (70 to 80 in-lb). 7. Apply a coat of Super Lube oil (Toro Part No. 145-5053) to the seal and assemble the access cover to the generator/motor controller. with the 2 capscrews. 8. Assemble the generator cover to the generator/motor and the controller with the 6 capscrews. Torque the capscrews to 8 to 9 N∙m (70 to 80 in-lb). 9. Insert the seal-brushes into the groove of the top and bottom intake shrouds. 10. Align the top and bo
- P0A3BError codeT7 Generator Motor - High Temp Warning .........................................................................8-454
- P0A5AError codeT7 Generator Current Sensor Out of Range......................................................................8-464
- P0A5CError codeT7 Generator Hardware DC Over Current .........................................................................8-466
- P0A36Error codeT7 Generator - Temperature Sensor Failure ......................................................................8-453
- P0AE6Error codeT7 Precharge Failure...............................................................................................................8-498
- P1Error codeCasappa 4 section, positive displacement gear type pump 0.50 Cubic Inches (8.3 cc) 0.66 Cubic Inches (10.8 cc) 0.37 Cubic Inches (6.1 cc) 0.24 Cubic Inches (3.9 cc)
- P1B01Error codeT7 Generator Motor - High Temp Shutdown.......................................................................8-636
- P1B2CError codeT7 Generator Motor - Stall......................................................................................................8-661
- P1B4CError codeT7 Generator Hardware Over Voltage.................................................................................8-706
- P1B6CError codeT7 Generator Internal Hardware Failure.............................................................................8-709
- P1B11Error codeT7 Generator Motor - High Temp Shutdown.......................................................................8-641
- P1B20Error codeT7 Generator Motor Speed Sensor Out of Range ............................................................8-646
- P1B21Error codeT7 Generator Motor Speed - High.........................................................................................8-658
- P1B31Error codeT7 Generator Motor Internal Regulator Voltage - High ....................................................8-677
- P1B41Error codeT7 Generator Bus Voltage - High ..........................................................................................8-680
- P1B42Error codeT7 Generator Bus Voltage - Low ...........................................................................................8-692
- P1B51Error codeT7 Generator Hardware Phase Over Current ....................................................................8-708
- P11C9Error codeT1 Speed Sensor 1 - Invalid Calibration Data....................................................................8-634
- P063CError codeT7 Generator Logic Voltage - Low........................................................................................8-422
- P063DError codeT7 Generator Logic Voltage - High .......................................................................................8-438
- P100CError codeT1 Engine Coolant Temperature Above Threshold - PTO Kill........................................8-524
- P100DError codeT1 Engine Coolant Temperature Above Threshold - Engine Kill...................................8-529
- P110CError codeT1 Traction Coil 1 FWD - Validation Failure - Current Converge...................................8-551
- P110DError codeT1 Traction Coil 1 FWD - Validation Failure - PWM Converge.......................................8-558
- P110EError codeT1 Traction Coil 1 FWD - Feedback Measurement Validation Failure..........................8-564
- P111CError codeT1 Traction Coil 1 REV - Validation Failure - Current Converge ....................................8-576
- P111DError codeT1 Traction Coil 1 REV - Validation Failure - PWM Converge........................................8-583
- P111EError codeT1 Traction Coil 1 REV - Feedback Measurement Validation Failure...........................8-589
- P210EError codeT1 Traction Pedal 1 Sensor/Switch Analog vs Analog Conflict......................................8-711
- P0628Error codeT1 Fuel Pump Output - Short to Ground/Overcurrent.......................................................8-406
- P0629Error codeT1 Fuel Pump Output - Short to Battery...............................................................................8-412
- P0670Error codeT1 Glow Plug Output - Open Circuit......................................................................................8-416
- P1015Error codeT1 Fuel Actuator - Open Circuit..............................................................................................8-539
- P1165Error codeT1 Swashplate 1 - Signal Open Circuit.................................................................................8-603
- P1167Error codeT1 Swashplate 1 - Validation Failure - Position Converge...............................................8-610
- P1189Error codeT1 Traction Pump 1 - Invalid Calibration Data ....................................................................8-630
- P2130Error codeT1 Traction Pedal Analog Sensor 2 - Short to Ground.....................................................8-721
- P2132Error codeT1 Traction Pedal Analog Sensor 2 - Open Circuit............................................................8-731
- P2502Error codeT1 Alternator Failure.................................................................................................................8-742
- P2530Error codeT1 Key Start/Run Correlation Fault.......................................................................................8-761
- R1Error code2500 PSI (172 bar) 3500 PSI (241 bar)
- R3Error code3625 PSI (250 bar)
- R4Error codeParker orbital rotor motor, TG Series Eaton geroler motor, Delta Series
- R5Error code200 PSI (14 bar)
- R6Error code2000 PSI (138 bar)
- R7Error code500 PSI (34 bar)
- R10Error code1000 PSI (69 bar)
- RM5210Error codeSauer- Danfoss gear motor 0.73 Cubic Inches (12 cc)
- RM5510Error codeBosch gear motor 1.18 Cubic Inches (19.3 cc) 1500 PSI (103 bar)