Toper endüstriyel öğütme makinesi All models error codes
Codes
- 1-3Error codeLow engine oil pressure occurred
- 1-4Error codeEngine alternator fault occurred
- 1-5Error codeCharging system voltage was incorrect (check charging system)
- 1-6Error codeInternal ECM fault
- 2-5Error codeLeak in hydraulic system detected by optional leak detector (reels shutdown and leak detector alarm sounds)
- 3-1Error codeGlow plug relay current was too high (check glow plug circuit)
- 3-2Error codeStart relay current was too high (check starting circuit)
- 3-3Error codeFuel stop solenoid and fuel pump current were too high
- 3-5Error codeMSV2 current was too high (check front mow electrical circuit)
- 4-1Error codeSV1 current was too high (check cutting unit lift electrical circuit)
- 4-2Error codeSV3 current was too high (check cutting unit lift electrical circuit)
- 4-3Error codeSV2 current was too high (check cutting unit lift electrical circuit)
- 4-4Error codeSVRV current was too high (check cutting unit lift electrical circuit)
- 4-5Error codeMSV1 current was too high (check rear mow electrical circuit)
- 5-1Error codeSignal from optional leak detector was lost
- 5-4Error codeInternal ECM fault
- C10E5Error codeT1 48V Logic Enable - Open Circuit................................................................8-42
- C180CError codeT2, T3, T4, T5, T6 Cutting Unit Motor - High Temp Warning..........................................8-148
- C181CError codeT2, T3, T4, T5, T6 Cutting Unit Motor Controller - High Temp Warning.......................8-189
- C1025Error codeT1 Park Brake Disengage - Open Circuit .......................................................8-23
- C1415Error codeT1 Solenoid 1 - Open Circuit..............................................................................8-61
- C1425Error codeT1 Solenoid 2 - Open Circuit..............................................................................8-80
- C1435Error codeT1 Solenoid 3 - Open Circuit..............................................................................8-99
- C1445Error codeT1 Solenoid 4 - Open Circuit............................................................................8-118
- C1801Error codeT2, T3, T4, T5, T6 Cutting Unit Motor - High Temp Shutdown .......................................8-124
- C1811Error codeT2, T3, T4, T5, T6 Cutting Unit Motor Controller - High Temp Shutdown ....................8-169
- C1820Error codeT2, T3, T4, T5, T6 Cutting Unit Motor Speed Sensor - Out of Range...........................8-204
- C1821Error codeT2, T3, T4, T5, T6 Cutting Unit Motor Speed Sensor - Cutting Unit Motor Speed -
- C1822Error codeT2, T3, T4, T5, T6 Cutting Unit Motor - Stall.......................................................................8-228
- C1831Error codeT2, T3, T4, T5, T6 Cutting Unit Motor Internal Regulator Voltage - High.....................8-234
- C1832Error codeT2, T3, T4, T5, T6 Cutting Unit Motor Internal Regulator Voltage - Low......................8-237
- C1841Error codeT2, T3, T4, T5, T6 Cutting Unit Motor Logic Voltage - High ............................................8-249
- C1842Error codeT2, T3, T4, T5, T6 Cutting Unit Motor Logic Voltage - Low .............................................8-264
- C1851Error codeT2, T3, T4, T5, T6 Cutting Unit Motor Bus Voltage - High...............................................8-282
- C1852Error codeT2, T3, T4, T5, T6 Cutting Unit Motor Bus Voltage - Low................................................8-293
- C1861Error codeT2, T3, T4, T5, T6 Cutting Unit Motor - Over Current.......................................................8-301
- ely10Error codeParking brake is engaged. Operator is raising from the seat (seat switch not fully depressed). Seat switch or circuit wiring is faulty. Ignition switch or circuit wiring is faulty
- i1Error codenspection passed. eave main-harness connector P59 unplugged from swash plate-angle ensor.
- is2Error code1. 2. refer to Connecting and Disconnecting the 48V Battery System, page 7-8. 3.
- O1Error codene or more tests failed. . . Plug seat-harness connector P03 or P04 into the micro switch. . Plug main-harness connector P51 into seat-harness connector P51. . . . .
- On1Error codee or more inspections failed. Leave main-harness connector P32 unplugged from 48V Enable Relay.
- P0115Error codeT1 Engine Coolant Temp Sensor - Open Circuit ................................................................8-305
- P0116Error codeT1 Engine Coolant Temp Sensor - Out of Range...............................................................8-311
- P0117Error codeT1 Engine Coolant Temp Sensor - Short to Ground..........................................................8-320
- P0225Error codeT1 Traction Pedal 1 Analog Sensor 1 - Open Circuit........................................................8-326
- P0227Error codeT1 Traction Pedal Analog Sensor 1 - Short to Ground.....................................................8-336
- P0524Error codeT1 Oil Pressure Low - Kill Engine..........................................................................................8-358
- P0575Error codeT1 Cruise Control Switch Correlation Fault.........................................................................8-365
- P0615Error codeT1 Start Output - Open Circuit................................................................................................8-378
- P0627Error codeT1 Fuel Pump Output - Open Circuit.....................................................................................8-400