Toper endüstriyel öğütme makinesi All models error codes
Codes
- RM5610Error codeSauer- Danfoss Steering Unit, Type OSPMS
- SV1Error codeSolenoid valve
- SV4Error codeSolenoid valve, relief valve
- T1Error codehe inspection is good. . Leave main harness connector P37 unplugged from the generator/ motor controller. .
- T2Error codeCutting unit 1 motor controller
- T3Error codeCutting unit 2 motor controller
- T4Error codeCutting unit 3 motor controller
- T5Error codeCutting unit 4 motor controller
- T6Error codeCutting unit 5 motor controller
- T7Error codeGenerator/motor controller
- Th1Error codee fault did not repeat. If the hood is open, close and latch it. Go to Returning the Machine to Service, page 7-23
- The95Error codeinverter/controller measured its internal temperature exceeded C (203° F). The inverter/controller broadcasts the Cutting t Motor Controller - High Temp Warning message on the N bus. te: When this fault is active, the primary controller broadcasts a ssage to all inverter/controllers to linearly reduce the current limit he motors. motor controller is also known as the inverter/controller
- The100Error codeinverter/controller measured its internal temperature exceeded ° C (212° F). The inverter/controller broadcasts the Cutting t Motor Controller - High Temp Shutdown message on CAN bus. te: When this fault is active, the primary controller broadcasts a ssage to all inverter/controllers to shut off the motors. motor controller is also known as the inverter/controller
- U111FError codeT2, T3, T4, T5, or T6 Source ID - CU Motor ID Out of Range.........................................8-882
- U0120Error codeT1/T7 CAN Bus Communication Fault - Generator ..........................................................8-775
- U0156Error codeT1/SC1 CAN Bus Communication Fault - IC......................................................................8-801
- U1022Error codeT1 TEC Fuse 2 Failure.............................................................................................................8-830
- U1023Error codeT1 TEC Fuse 3 Failure.............................................................................................................8-837
- U1024Error codeT1 TEC Fuse 4 Failure.............................................................................................................8-844
- U1025Error codeT1 TEC Fuse 5 Failure.............................................................................................................8-851
- U1117Error codeT1 Source Address Contention Fault....................................................................................8-880
- U1122Error codeT1, T2 CAN Bus Communication Fault - CU Motor 1 .......................................................8-920
- U1123Error codeT1, T3 CAN Bus Communication Fault - CU Motor 2 .......................................................8-928
- U1124Error codeT1, T4 CAN Bus Communication Fault - CU Motor 3 .......................................................8-937
- U1125Error codeT1, T5 CAN Bus Communication Fault - CU Motor 4 .......................................................8-945
- U1126Error codeT1, T6 CAN Bus Communication Fault - CU Motor 5 .......................................................8-954
- U1301Error codeT1, T2 Software Version Incompatibility - CU Motor 1......................................................8-966
- U1302Error codeT1, T3 Software Version Incompatibility - CU Motor 2......................................................8-968
- U1303Error codeT1, T4 Software Version Incompatibility - CU Motor 3......................................................8-970
- U1314Error codeT1, T5 Software Version Incompatibility - CU Motor 4......................................................8-979
- U1315Error codeT1, T6 Software Version Incompatibility - CU Motor 5......................................................8-982
- U1501Error codeT1, T2, T3, T4, T5, T6, T7 48V System Logic Voltage - High.........................................8-984
- U1502Error codeT1, T2, T3, T4, T5, T6, T7 48V System Logic Voltage - Low..........................................8-996
- U1511Error codeT2, T3, T4, T5, T6, T7 Cutting Unit Motor Bus Voltage - High ..................................... 8-1013
- U1512Error codeT2, T3, T4, T5, T6, T7 Cutting Unit Motor Bus Voltage - Low...................................... 8-1022
- U1701Error codeT1 Board Internal Error - IPE............................................................................................... 8-1034