Physio-Control All models error codes
Codes
- a12aError codeDE ERROR XFER PADDLE (Defib HW error.) _ _ _
- a12cError codeDE ERROR CHG INHIBIT (Defib HW error.) _ _ _
- a12dError codeDE ERROR CHG ENABLE FAIL (Charge enable feedback indicates not charging.) _ _ _ _
- a12eError codeDE ERROR BTE FAULT (Cedar BTE Fault Line State.) _ _ _
- a12fError codeDE ERROR BTE FAULT CLEARED (Cedar BTE Fault Line State.) _ _ _ _
- a20dError codePA ERROR PACE OVERRUN (Pacing pulse process overrun. Set current to zero.) _ _ _
- a20eError codePA ERROR PULSE WIDTH (Pacing pulse too long.) _ _ _
- a20fError codePA ERROR A2D INT (Internal A/D conversion timeout. Set current to zero.) _ _ _
- a21aError codePA ERROR CAL CURRENT (Current calibration failed.) _ _ _
- a21bError codePA ERROR CAL Z 300 (Impedance 300 calibration failed.) _ _ _ _
- a21cError codePA ERROR CAL CURRENT CRC (Current cal table corrupt.) _ _ _ _
- a21dError codePA ERROR CAL IMPEDANCE CRC (Impedance cal values corrupt.) _ _ _ _
- a21eError codePA ERROR CAL Z 0 (Impedance 0 calibration failed.) _ _ _ _
- a21fError codePA ERROR PACE I (Current present when not pacing.) _ _ _
- A22Error codeBiphasic PCB
- A23Error codeCO2 PCB Assembly
- a130Error codeDE ERROR BTE RESET (Defib HW error.) _ _ _
- a131Error codeDE ERROR NO BTE HW (Biphasic HW not found.) _ _ _ _
- a132Error codeDE ERROR NO BTE XFER (Defib HW error.) _ _ _ _
- a133Error codeDE ERROR BTE CEDAR DRV HI (A/D high bit sticky.) _ _ _ _ _
- a201Error codePA ERROR LONG WDT (Long watchdog timer test failed.) _ _ _
- a202Error codePA ERROR SHORT WDT (Short watchdog timer test failed.) _ _ _
- a203Error codePA ERROR SCI RCV (SCI received overrun, framing or parity. Unit used near high EMI causing these issues.) _ _ _
- a204Error codePA ERROR 2MS OVERRUN (2 ms ECG sampling overrun.) _ _ _
- a208Error codePA ERROR MSG RESYNC (Received message incomplete.) _ _ _
- a209Error codePA ERROR MSG SIZE (Received msg size error/input buff full.) _ _ _
- a210Error codePA ERROR A2D EX (External A/D conversion timeout. Current set to zero.) _ _ _
- a211Error codePA ERROR SPI (SPI transfer timeout. Current set to zero.) _ _
- a212Error codePA ERROR RAM TEST (RAM test failed. Reset Pacer Processor.) _ _ _
- a213Error codePA ERROR ROM TEST (ROM CRC test failed.) _ _ _
- a214Error codePA ERROR CPU TEST (Stack overrun occurred.) _ _ _
- a215Error codePA ERROR STACK CHECK (Isolated +5 V ref. out of range.) _ _ _
- a216Error codePA ERROR V ISO MON (HV present when not pacing.) _ _ _ _
- a217Error codePA ERROR V 12V MON (+12 V voltage out of range.) _ _ _ _
- a218Error codePA ERROR V HVIS SENSE (HV present when not pacing.) _ _ _ _
- a219Error codePA ERROR V HVIS (HVIS voltage out of range.) _ _ _
- a220Error codePA ERROR NO HVIS SENSE (No HV present when pacing.) _ _ _ _
- a221Error codePA ERROR EXT A2D TEST (External A/D test register reset failed.) _ _ _ _
- a222Error codePA ERROR NO CAL HVIS SENSE (No HV present before current cal.) _ _ _ _ _
- a223Error codePA ERROR NO Q4 SENSE (No Q4 sense when not pacing [Q4 shorted].) _ _ _ _
- a224Error codePA ERROR Q4 SENSE (Q4 sense present when pacing [CR25 open].) _ _ _
- b001Error codePR ERROR TEMP TOO LOW (Printhead ADC reading too low; param = ADC value. May be associated with UT ERROR DAC FAILURE and _ _ _ _ _ _ _ UT ERROR ADC READ.) _ _ _
- b002Error codePR ERROR TEMP TOO HIGH (Printhead ADC reading too high; param = ADC value. May be associated with UT ERROR DAC FAILURE _ _ _ _ _ _ _ and UT ERROR ADC READ.) _ _ _
- b003Error codePR ERROR SELF TEST FAIL (Invalid CRC read from HW; param = ADC value.) _ _ _ _
- b004Error codePR ERROR WRONG PRINTER TYPE (Saw incorrect printer for config; 50/100 mismatch.) _ _ _ _
- c008Error codePM ERROR LOST COMMS (Lost communications with power PCB.) _ _ _
- c009Error codePM ERROR CLOCK FAILURE (Power PCB is running on its internal oscillator block because it detected an external clock failure.) _ _ _
- CO2Error codeBattery Pins/Power PCB Cable- Edmark
- d003Error codeSC ERROR SCI FRAME (SCI frame error.) _ _ _
- d004Error codeSC ERROR SCI PARITY (SCI parity error.) _ _ _