Nokia switch All models error codes
Codes
- 4Error codeSP-%c memory read error at address 0x%x - recoverable
- 35Error codeIndicates the protection SP failed to run its diagnostics, boot the operational code and begin messaging with the working SP in the allotted time. Corrupted disk file system on the Protection SP or software or CPU subsystem error on the Protection SP
- 36Error codeIndicates the protection SP failed to get all the call and configuration data during the time allotted for synchronizing the protection SP. NOTE: the software retries synchronization 5 times before recording this fault. Software or CPU subsystem error
- 37Error codeIndicates the device that holds the equipment identification code and version information cannot be read by the system processor. Faulted SP
- 39Error codePower Source %c lost voltage
- 40Error codePower Source %c on %s lost voltage
- 41Error codePower Source %c on %s did not report loss of voltage
- 42Error codePower Source %c voltage restored
- 43Error codePower Source %c on %s voltage restored
- 44Error codePower Source %c on %s did not report voltage restored
- 45Error codeModule in slot %d has a TSU or FSU Fault
- 46Error codeModule in slot %d has a TSU or FSU MLBA Parity Error
- 47Error codeModule in slot %d has a MLINK Fault
- 48Error codeFan unit or fuse fault
- 49Error codeFan unit or fuse fault has been cleared
- 311Error codeIndicates a software error. Corrupted disk file system or software or CPU subsystem error
- 312Error codeIndicates a software error. Corrupted disk file system or software or CPU subsystem error
- 313Error codeIndicates a software error. Corrupted disk file system or software or CPU subsystem error
- 314Error codeIndicates a software error. Corrupted disk file system or software or CPU subsystem error
- 315Error codeIndicates a software error. Corrupted disk file system or software or CPU subsystem error
- 316Error codeIndicates a software error. Corrupted disk file system or software or CPU subsystem error
- 317Error codeIndicates a software error. Corrupted disk file system or software or CPU subsystem error
- 319Error codeIndicates a software error. Corrupted disk file system or software or CPU subsystem error
- 320Error codeIndicates a software error. Corrupted disk file system or software or CPU subsystem error
- 321Error codeIndicates a software error. Corrupted disk file system or software or CPU subsystem error
- 323Error codeIndicates a software error. Corrupted disk file system or software or CPU subsystem error
- 326Error codeIndicates a software error. Corrupted disk file system or Software or CPU subsystem error
- 328Error codeSP-%c PSF %d update sequence error - cause %d
- 329Error codeSP-%c PSF %d memory failure - cause %d
- 330Error codeSP-%c PSF %d general alarm - cause %d
- 331Error codeUpdate failure on the Stby SP-%c
- 332Error codeSP-%c to %s relay channel %d communication error - cause %d
- 333Error codeSP-%c to %s relay channel %d communication error - cause %d
- 335Error codeIndicates a software error. Corrupted disk file system or Software or CPU subsystem error
- 352Error codeMTP3 - T17 exprd - align failure - reattempt - linkId %d on %s
- 353Error codeIndicates an SS7 link is Out of Service due to a faulted facility (T1) or IOM. Faulted facility (T1) or faulted IOM running MTP2
- 367Error codeIndicates the remote SS7 link has been blocked by the remote end. A maintenance operation has blocked the link
- 372Error codeIndicates a congestion threshold has been crossed for SS7 messaging over a link. Call volumes are larger than planned or Equipment or facility faults have caused a large number of releases. Check for facilities faults, Check for SS7 link faults on other links
- 374Error codeMTP2 - abnrml BSN - protocol error - linkId %d on %s
- 375Error codeMTP2 - abnrml FIB - protocol error - linkId %d on %s
- 420Error codeDestination is inaccessible to MTP3 as determined by routing managementFailure on a remote Point Code device (SCP, SSP), link failures, faulted IOM
- 422Error codeIndicates a congestion threshold has been crossed for SS7 messaging to a Point Code. Call volumes are larger than planned or Equipment or facility faults have caused a large number of releases
- 465Error codeISUP - bind failure within the given time
- 468Error codeThis alarm is obsolete
- 469Error codeIndicates a software error. Corrupted disk file system or Software or CPU subsystem error
- 470Error codeIndicates a software error. Corrupted disk file system or Software or CPU subsystem error
- 478Error codeIW - Bind failure
- 487Error codeIW - memory alloc failure
- 489Error codeCC - memory alloc failure
- 490Error codeCC - connID insertion failure into SuInst hash tbl