Nokia switch All models error codes
Codes
- 5Error codeSP-%c bus error at address 0x%x
- 6Error codeSP-%c kernel fault
- 50Error codeChassis over temperature fault
- 51Error codeChassis over temperature fault cleared
- 52Error codeFan unit has been removed
- 53Error codeFan unit has been inserted
- 54Error codeIndicates the module booted but communications through the switch fabric could not be established. A component fault on the IOM that was not caught by diagnostics
- 56Error codeIndicates the module booted and communications from the SP to the IOM was established, the module failed to accept the configuration state. Faulted IOM or SF
- 57Error codeThe rear module in a slot has been removed from the chassis or is not detected to be present. Operator Error or faulted IOM
- 58Error codeThe rear module in a slot has been removed from the chassis or is not detected to be present. Maintenance procedure or faulted IOM
- 59Error codeIndicates the rear module is missing (either not detected to be in the chassis or not in the chassis). To get this alarm, the front module must be provisioned and present in the chassis
- 60Error codeThe rear module in a slot has been removed from the chassis or is not detected to be present. Maintenance procedure or faulted IOM
- 62Error codeThe SF front module has been removed from the chassis or is not detected to be present. Maintenance or faulted SF
- 64Error codeThe SP front module has been removed from the chassis or is not detected to be present. Maintenance or faulted SF
- 491Error codeCC - connID insertion failure into SpInst hash tbl
- 492Error codeCC - connID lookup failure into SuInst hash tbl
- 493Error codeCC - connID lookup failure into SpInst hash tbl
- 494Error codeCC - lookup failure of intfc ID in the intfc hash tbl
- 498Error codeCC - evnt map failure between 2 nrwband ISDN intfcs
- 499Error codeCC - evnt map failure between 2 nrwband DSS1 intfcs
- 500Error codeCC - evnt map failure from nrwband DSS1 to nrwband ISDN intfc
- 501Error codeCC - evnt map failure from nrwband ISDN to nrwband DSS1 intfc
- 529Error codeIW - bind failure on a lower SAP towards ISUP RM
- 533Error codeQW - bind failure to ISDN layer
- 540Error codeA large percentage of a trunkgroup has been provisioned out of service or has autonomously gone OOS due to a transmission failure. Facilities fault or provisioning
- 543Error codeDPC %s - CIC %d locally blocked
- 544Error codeDPC %s - CIC %d remotely blocked
- 547Error codeDPC %s - CIC %d - Range %d locally blocked
- 548Error codeDPC %s - CIC %d - Range %d remotely blocked
- 568Error codeLAPD - Protocol error - IntfcId %d linkId %d on %s
- 587Error codeQ931 - Bind failure - IntfcId %d linkId %d on %s
- 590Error codeQ931 - Msg decode error - IntfcId %d linkId %d on %s
- 616Error codeInfo
- 617Error codeInfo
- 618Error codeInfo
- 619Error codeInfo
- 621Error codeInfo
- 622Error codeInfo
- 625Error codeTSMC - Error synchronizing standby
- 631Error codeIndicates an UNI is not communicating. Missing or faulted equipment modules or not provisioned
- 635Error codeThe switch has lost ATM ILMI management communication with the ATM switch. This indicates an ATM cell flow problem IOM fault or Cabling fault or Provisioning
- 638Error codeIndicates an AAL1 or AAL2 endpoint is out of service because of missing equipment or a faulted equipment modules
- 639Error codeIndicates an AAL1 or AAL2 endpoint is out of service because it is failing to set up an SVC to the remote endpoint. Faulted voice over packet facilities, e.g. LOS/LOF on ATM interface or Equipment at remote endpoint faulted or not provisioned
- 643Error codeIndicates an AAL1 or AAL2 endpoint is out of service because of missing equipment or a faulted equipment
- 644Error codeIndicates an AAL1 or AAL2 endpoint is out of service because it is failing the connectivity test with the remote equipment. Faulted voice over packet facilities, e.g. LOS/LOF on ATM interface or Equipment problem at remote endpoint
- 648Error codeIndicates the receiver on an OC3 or OC12 interface is NOT detecting a signal. Possible cabling fault, provisioning error or faulted IOM
- 650Error codeIndicates the receiver on an OC3 or OC12 interface is NOT detecting framing. Possible cabling fault, provisioning error or faulted IOM
- 652Error codeIOM-%d-%d Alarm Indication Signal
- 653Error codeIOM-%d-%s Alarm Indication Signal cleared
- 654Error codeIOM-%d-%d Remote Alarm Indication