MAN gemi jeneratörü All models error codes
Codes
- 3402Error codePresent glow plugs. Priority 3: Display during standstill. Fault: 10. On. Pinout A302: ZE / 19
- 3403Error codeGlow plugs present. Priority 3: Display during stop. Fault: Very low 2; 3. Unacceptable; 10. Pinout A302: ZE / 20
- 3500Error codeDefective trailer ABS (ABS, ASR, EBS). Priority 5: Display when stopped and driving. Fault: Fault 0 missing or defective control unit. Pinout A302: X / 2
- 3501Error codeTrailer ABS, power consumption. Priority 5: Display during stopping and driving. Fault: 1. too high; 5. Short circuit to ground; 6. Short circuit to Ubat; 10. Pinout A302: R2 / 14
- 3502Error codeTractor brake signal. Priority 2: Fault requiring removal of service center. Fault: 1. too high; 2. too low; 5. 6. Shutdown nUbat.; 10. Pinout A302: R2 / 4
- 3503Error codeBrake signal trailer. Priority 2: Malfunction requiring removal of the service center. Malfunction: 1. too high; 2. too low; 5. 6. Shutdown nUbat.; 10. Pinout A302: R2 / 5
- 3568Error codeRetarder engaged. Fault: Fault 0 missing or faulty control unit
- 3569Error codeMotor brake engaged. Fault: Fault 0 missing or control unit faulty
- 3570Error codeService brakes included. Fault: Fault 0 missing or faulty control unit
- 3600Error codeClutch fluid level. Priority 5: Display during stop and driving. Fault: 6. Short circuit to Ubat.; 10. Pinout A302: R1 / 2
- 3602Error codeRelay reversing lamp. Priority 5: Display during stopping and driving. Fault: 5. Short circuit to ground; 6. Short circuit to Ubat; 10. Pinout A302: F2 / 13
- 3603Error codeAutopleniaKongsberg system is spinning. Priority 5: Display during stopping and driving. Fault: 5. Short circuit to ground; 6. Short circuit to Ubat; 10. Pinout A302 M / 18
- 3625Error codeCreep speed. Priority 2: Fault requiring removal of service center. Fault: Short circuit to Ubat 6. Pinout A302: X / 4
- 3671Error codeEEPROM calibration memory. Error in EEPROM test. Malfunction in memory unit EDC circuit due to power failure or errors in saving data
- 3676Error codeFault over-triggering mechanism (After operating test). Checking the output stage injectors in inertia driving mode. The engine is shut down
- 3678Error codeVoltage of capacitor unit 1.
- 3679Error codeVoltage capacitor unit 2.
- 3687Error codepressure limiting valve. Pressure relief valve does not open. Control valve. Engine off
- 3693Error codeSwitching voltage injector. No injection
- 3732Error codeOvervoltage Test. Defective device for overvoltage testing
- 3735Error codeTemperature EDC unit. Temperature sensor voltage test. Giving the equivalent of 60°
- 3736Error codeoutput stage. Output stage shutdown. Faulty safety connection or short circuit to higher voltage. Motor shut down
- 3744Error codeoutput stage (Highside) EGR valve. Checking the output stage for open or short circuit
- 3745Error codeoutput stage (Highside) boost pressure. Checking the output stage for open or short circuit
- 3746Error codeoutlet stage (Highside) exhaust gas recirculation. Checking the outlet stage for open or short circuit
- 3748Error codeoutput stage (Highside) unit dosage high pressure pump. Checking the output stage for open or short circuit
- 3749Error codeoutput stage (Highside) holding valve. Checking the output stage for open or short circuit
- 3751Error codeoutput stage (Highside) starter relay. Checking the output stage for open or short circuit
- 3752Error codeSensor camshaft speed. Missing or incorrect signal from sensor. Engine continues to operate using crankshaft position sensor
- 3753Error codecrankshaft speed sensor. Missing or incorrect signal from sensor. The engine continues to operate using the camshaft position sensor
- 3754Error codeSystem initialization error. Errors in control test. Engine does not start or stops
- 3755Error codeFuel pressure.
- 3756Error codesensor voltage AGR. Sensor readings are incorrect or missing
- 3758Error codeError Messages 2. Violation of Master-Slave data sharing (for V-shaped engine). The load on the data channel is probably too high. The Slave control unit blocks the fuel supply until the connection is reestablished. The engine will only start when the Master is at half power
- 3759Error codeError Messages 3. Violation of Master-Slave data exchange (for V-shaped engine). The load on the data channel is probably too high. The Slave control unit blocks the fuel supply until the connection is reestablished. The engine will only start when the Master is at half power
- 3760Error codeError Messages 4. Violation of Master-Slave data exchange (for V-shaped engine). The load on the data channel is probably too high. The Slave control unit blocks the fuel supply until the connection is reestablished. The engine will only start when the Master is at half power
- 3761Error codeError Messages 5. Violation of Master-Slave data exchange (for V-shaped engine). The load on the data channel is probably too high. The Slave control unit blocks the fuel supply until the connection is reestablished. The engine will only start when the Master is at half power
- 3762Error codeReception error CANdekodera master / slave, CAMD-ANA reported. Violation of Master-Slave data exchange (for V-shaped engine). CAN reception error decoder Master / Slave. Slave control unit blocks fuel supply until connection is reestablished. Engine starts only when Master unit is at half power
- 3763Error codeCAN reception error decoder master/slave, CAMD-CMOL reported. Violation of Master-Slave data exchange (for V-shaped engine). CAN reception error decoder Master/Slave. Slave control unit blocks fuel supply until connection is reestablished. Engine starts only when Master unit is at half power
- 3764Error codeCAN reception error decoder master/slave reports CAMD-CONTROL. Violation of Master-Slave data exchange (for V-shaped engine). CAN reception error decoder Master/Slave. Slave control unit blocks fuel supply until connection is reestablished. Engine starts only when Master unit is at half power
- 3765Error codeCAN reception error decoder master / slave, CAMD-FFR1pereryv. Violation of Master-Slave data exchange (for V-shaped motor). CAN reception error decoder Master / Slave. Response system is not available, the motor is operating normally
- 3766Error codeDecoder CAN master/slave receiving error, CAMD-FFR2 interrupt. Violation of Master-Slave data exchange (for V-shaped motor). CAN receiving error decoder Master/Slave. Response system is not available, the motor is operating normally
- 3767Error codeError during decoder CAN master/slave receiving, CAMD-FFR3 interrupt. Violation of Master-Slave data exchange (for V-shaped motor). CAN receiving error decoder Master/Slave. Response system is not available, motor is operating normally
- 3768Error codeCAN reception error decoder master / slave, CAMD initialization. Violation of Master-Slave data exchange (for V-shaped motor). CAN reception error decoder Master / Slave. Response system is not available, engine is operating normally
- 3769Error codeCAN reception error decoder master / slave, CAMD-LIMITpereryv. Violation of Master-Slave data exchange (for V-shaped engine). CAN reception error decoder Master / Slave. Slave control unit blocks fuel supply until connection is reestablished. Engine starts only when Master unit is at half power
- 3771Error codeMaster/Slave, data channel failure. Master or Slave failure during reception of FFR-CAN data
- 3775Error codeline pressure. At low line pressure, the motor may stop
- 3776Error codeline pressure. Main pressure is low and cannot be increased to normal pressure
- 3777Error codeline pressure. A main and high pressure cannot be reduced to normal pressure
- 3778Error codeline pressure. Leak under overflow. Perhaps opening of control valve