MAN gemi jeneratörü All models error codes
Codes
- 3088Error codeCharge air pressure sensor in the pipe after the boost intercooler.
- 3089Error codeTemperature sensor before charge air enters cylinders (posleAGR).
- 3091Error codeCoolant temperature sensor. Torque reduced by 10%. An equivalent temperature reading of 100.4 °C is displayed
- 3097Error codeFuel temperature sensor. Sensor not installed
- 3099Error codepressure sensor line.
- 3100Error codeFuel pressure sensor (low pressure side).
- 3101Error codeLeft rear axle level sensor
- 3102Error codeRight rear axle level sensor
- 3103Error codeLevel sensor front axle
- 3104Error codeZBR2 voltage supply, analog ground. Pinout A302: R1 / 15
- 3107Error codeZBR2 voltage supply, contact open (relay terminal 15). Priority 2: Fault requiring removal of the service center. Fault: 5. 10. Pinout A302: F2 / 12
- 3108Error codeZBR2 voltage supply batteries power switch. Priority 5: Display during stopping and driving. Fault: 5. 10. Pinout A302: F2 / 18
- 3111Error codeZBR2 voltage supply, starter switch (terminal 50). Priority 1: Requires engine shutdown. Priority 2: Fault requiring removal of service center. Priority 3: Display during standstill. Priority 4: No display does not affect operability. Priority 5: Display during standstill and while driving. Pinout A302: ZE / 5
- 3120Error codeLIN bus / LIN - Local Link Network. Cause: Fault Wiring harness.
- 3130Error codeCoolant Pressure. Fault condition: FMI 1 too high / FMI 2 too low. Cause: high or low pressure in the cooling circuit, faulty high/low pressure switch (B203), faulty wiring harness.
- 3150Error codeAnother option is the body control unit. Error status: FMI 9, device failure. Cause: The heating cabin control unit (A474) and the heater/air conditioning control unit (A250) options are incompatible.
- 3151Error codeLeft rear axle pressure sensor
- 3152Error codeRight rear axle pressure sensor
- 3153Error codeFront axle pressure sensor
- 3154Error codeFront axle pressure sensor
- 3155Error codeSecond rear axle right level sensor
- 3156Error codeSecond rear axle left level sensor
- 3157Error codePressure sensor in the brake system
- 3158Error codePressure sensor suspension shaft
- 3160Error codeManagement body cells. 30, voltage. Fault condition: FMI 1 too high / FMI 2, too low. Cause: power supply terminals 30 cab heating control unit (A474) too high or too low, fault F128 fuse fault harness. 30, voltage" signal by means of a PC. Voltage measurement: Terminal 30; Heated driver's cab control unit (A474) - between Pin 3 (+) and Pin 6 (-): 16-32 (UBAT)
- 3170Error codeSensor steering angle
- 3200Error codeSolenoid valves, power supply or feedback
- 3201Error codeSolenoid valve 2/2, rear axle, left side
- 3202Error codeSolenoid valve 2/2, rear axle, right side
- 3203Error codeSolenoid valve 2/2, front axle
- 3204Error codeSolenoid valve 3/3, lifting axle, lifting or lowering
- 3205Error codeSolenoid valve 3/3, lifting axle, lifting or lowering
- 3206Error codeSolenoid valve 3/2, spare
- 3207Error codeSolenoid valve 3/3, lifting bellows
- 3208Error codeSolenoid valve 2/2, third axle, right side
- 3209Error codeSolenoid valve 2/2, third axle, left side
- 3212Error codeSolenoid valve, throttle cross
- 3216Error codeSolenoid valve 3/3, second lifting axle, lifting or lowering
- 3217Error codeSolenoid valve 3/3, second lifting axle, lifting or lowering
- 3260Error codeDamper valve, supply voltage or feedback
- 3261Error codeFront axle shock absorber valve
- 3262Error codeDump valve, first rear axle
- 3263Error codeDump valve, second rear axle
- 3300Error codeGenerator, W. Terminal Priority 2: Failure requiring service center removal. Failure: 3. Unacceptable. Pinout A302 M / 14
- 3301Error codeGenerator, L. Terminal Priority 2: Fault requiring removal of service center. Fault: 4. No signal. Pinout A302 M / 4
- 3302Error codeGenerator terminal B+. Priority 3: Display during stop. Fault: 5. 6. 10. Pinout A302 M/8
- 3303Error codeSignal D + (engine running). Priority 2: Fault requiring removal of the service center. Fault: 5. Short circuit to ground; 6. Short circuit to Ubat. Pinout A302: F2 / 17
- 3335Error codeSupply voltage (no data). Priority 4: No display, does not affect operability. Error: Error 0 missing or faulty control unit
- 3400Error codeSolenoid valve for preheating. Priority 3: Display during stop. Fault: 5. Short circuit to ground; 6. Short circuit to Ubat; 10. Pinout A302 M / 13
- 3401Error codeRelay preheat. Priority 3: Display during stop. Fault: 5. Short circuit to ground; 6. Short circuit to Ubat; 10. Pinout A302: ZE / 8