MAN gemi jeneratörü All models error codes
Codes
- 3864Error codeControl P1 injection. Insufficient voltage to first pre-injection. First pilot injection P1 blocked
- 3866Error codeControl M1 injection. Insufficient voltage to second main injection. Second main injection blocked
- 3867Error codeP0 injection control. Insufficient voltage for additional injection. Additional injection locked
- 3868Error codeIdentification of discharge air temperature after intercooler (intercooler).
- 3871Error codeDetection of temperature inside the block EDC.
- 3872Error codeIdentification of two temperatures in the EDC unit.
- 3903Error codeFuel temperature in tank 1. Priority 5: Display during stop and driving. Fault: 1. too high; 2. too low. Pinout A302: R1 / 10
- 3919Error codeNOx sensor overheating.
- 3920Error codeNOx concentration.
- 3921Error codeO2 concentration.
- 3923Error codeCoolant temperature 2. high or low temperatures, faulty wiring or contact in connectors.
- 3925Error codeCoolant temperature sensor 2.
- 3926Error codepressure sensor control line slope (RDS).
- 3927Error codeoxygen amount in the exhaust gas sensor (oxygen sensor). Low value of the sensor
- 3929Error codeAGR c controls the amount of oxygen sensor in the exhaust gas (lambda probe). MIL (malfunction indicator lamp) Error. Request MIL with blocked or unblocked AGR. For diagnosis of the NOx system, the value of the amount of oxygen sensor is checked (oxygen sensor). If the limit values from the sensor are exceeded, a request is sent to include the MIL
- 3930Error codeError PR (power reduction). Request PR with blocking or non-blocking AGR. If the control values from the sensor detect a low AGR operating coefficient and a correspondingly high NOx level, a power reduction request is sent
- 3932Error codeOutput stage (Lowside) pressure control Checking the charge air.
- 3936Error codeBoost pressure too high. The charge air pressure is exceeded depending on the engine speed and valve position
- 3938Error codeNo adaptation of the amount of oxygen in the exhaust gas sensor (oxygen sensor). Verification of the correction factor. sensor calibration is carried out in forced idle mode, and a working system reduces the risk of fault messages during exhaust gas recirculation
- 3942Error codePressure charge air intercooler after low pressure. Checking the charge air pressure, checking the reliability of the connection contacts
- 3943Error codePressure sensor after charge air intercooler low pressure.
- 3944Error codeTemperature charge air intercooler after low pressure. Checking the charge air temperature, checking the reliability of the connection contacts
- 3945Error codedischarge air temperature sensor after low pressure intercooler.
- 3946Error codeCooler injected high pressure air. Cooler thermostat failure or cooler pressure reducer failure
- 3947Error codeThe cooler is discharging low pressure air. Thermostat failure in the cooler or pressure reducing cooler failure
- 3963Error codeLIN (Local Area Network) Error. Checking for the presence of a signal
- 3965Error codeLIN (Local Area Network) Error. Checking for the presence of a signal
- 3966Error codeSelf-test of the oil level sensor. Checking the accuracy of the readings
- 3972Error codeMonitoring of low znacheniyaNOx. Low oxygen sensor amount in the exhaust gas value (lambda probe)
- 3973Error codeCharge air pressure in high pressure circuit. Air pressure is too high (FMI1) or too low (FMI2)
- 3974Error codeCharge air pressure in low pressure circuit. Air pressure is too high (FMI1) or too low (FMI2)
- 3975Error codeGap sensor cables.
- 3976Error codeMonitoring the fault status of the oxygen amount in the exhaust gas sensor (oxygen sensor). Checking the oxygen concentration. Perhaps due to a faulty sensor of expiration date
- 3978Error codeElectrical fault oxygen amount in exhaust gas sensor (oxygen sensor). Electrical fault output stage of control unit to sensor
- 3979Error codeThe amount of oxygen in the exhaust gas sensor (oxygen sensor). It was discovered that the amount of oxygen in the exhaust gas sensor (oxygen sensor) was ineffective
- 3980Error codeoil pressure. Deviation of the oil pressure sensor output at zero pressure
- 3981Error codeHigh exhaust back pressure. Improper vehicle operation
- 3983Error coderegulator AGR. Internal fault AGR regulator. Controller fault is received via data message
- 4000Error codePriority 5: Display during stopping and driving. Fault: 5. Short circuit to ground; 6. Short circuit to Ubat; 10. Pinout A302: F1/17
- 4001Error codeLow beam, left side. Priority 5: Display during stopping and driving. Fault: 5. Short circuit to ground; 6. Short circuit to Ubat; 10. Pinout A302: BL / 6
- 4002Error codeLow beam, right side. Priority 5: Display during stopping and driving. Fault: 5. Short circuit to ground; 6. Short circuit to Ubat; 10. Pinout A302: BR/2
- 4003Error codeLeft headlight leveling adjustment. Priority 5: Display during stopping and driving. Fault: Fault 0 missing or faulty control unit; 3. Unacceptable; 4. No signal; 8. Wrong signal; 9. Faulty component. Pinout A302: BL/3
- 4004Error codeRight headlight leveling adjustment. Priority 5: Display during stopping and driving. Fault: Fault 0 missing or faulty control unit; 3. Unacceptable; 4. No signal; 8. Wrong signal; 9. Faulty component. Pinout A302: BR / 6
- 4005Error codeTractor start, left rear. Priority 5: Display during stop and driving. Fault: 1. too high; 2. too low; 5. 6. Shutdown nUbat.; 10. On. Pinout A302: R2 / 1
- 4006Error codeTractor start, right rear. Priority 5: Display during stop and driving. Fault: 1. too high; 2. too low; 5. Short circuit to ground; 6. Short circuit to Ubat; 10. Pinout A302: R2 / 13
- 4007Error codeWhen starting the towing vehicle or the front left side. Priority 5: Display during stopping and driving. Fault: 1. too high; 2. too low; 5. 6. 10. Pinout A302: BL/4
- 4009Error codeThe key rotates the pointer, the Hall sensor (left on the steering wheel). Priority 5: Display during stopping and driving. Fault: Short circuit to Ubat 6.; Pinout A302: F1 / 3
- 4010Error codeThe key rotates the pointer, the Hall sensor (right on the steering wheel). Priority 5: Display during stopping and driving. Fault: Short circuit to Ubat 6.; Pinout A302: F1 / 6
- 4011Error codeLeft switch flashing light. Priority 5: Display during stopping and driving. Fault: 6. Short circuit to Ubat.; 10. Pinout A302: F1 / 15
- 4012Error codeRight switch flashing light. Priority 5: Display during stopping and driving. Fault: 6. Short circuit to Ubat.; 10. Pinout A302: F1 / 16