Xinje VFD-manual All models error codes
Codes
- Err17Error code1. Encoder model mismatch 2. Encoder connection error 3. Encoder damaged 4. Abnormal PG card
- Err18Error codeMotor short circuit to ground
- Err19Error codeVFD operation current is lower than P7-61
- Err20Error code1. Whether the load is too large or the motor stalls 2. The selection of frequency converter is too small
- Err21Error codeThe deviation between the motor parameters and the actual value is too large
- Err26Error code1、Reduce the load 2、Increase torque limit
- Err35Error code1、The VFD is tuned with a synchronous motor. 2、Set P1-24=1 to disable this alarm
- Err37Error codeChange the encoder's power battery
- Err43Error code1. Input the signal of external fault through multi-function terminal X 2. Input external fault signal through virtual Y function
- Err44Error code1. The upper computer is not working properly 2. The communication cable is abnormal 3. Communication parameter P9 group is set incorrectly
- Err48Error code1. Input user-defined fault 1 signal through multi-function terminal X 2. Input user defined fault 1 signal through virtual IO function
- Err49Error code1. Input user-defined fault 2 signal through multi-function terminal X 2. Input user defined fault 2 signal through virtual IO function
- Err51Error codeIn the process of inverter operation, change the current motor selection through the terminal
- Err52Parameter1. Encoder parameter setting incorrect 2. Motor blocked 3. Incorrect UVW wiring
- Err53Error code1. Incorrect setting of encoding parameters 2. The motor is not tuned 3. Unreasonable setting of motor over speed detection parameters P7-63 and P7-64
- Err54Error code1. Loose wiring of temperature sensor 2. Motor temperature too high
- Err55Error code1. The temperature sensor wiring is loose 2. Motor temperature is too high
- Err70Error code
- is3Error codeHızlı hızlanma sırasında, motorun durma olasılığı yüksektir. Bu, P5 -22 aşırı akım durma hareketi akım dengeleme katsayısını % 100 olarak ayarlayarak ayarlanabilir
- is323Error code
- P0-01Error codeFirst motor control mode
- P0-02Error codeOperasyon komut kanalı
- P0-03Error codeAna frekans kaynağı A kanal seçimi
- P0-04Error codeYardımcı frekans kaynağı B kanal seçimi
- P0-14Error codeÜst sınır frekans kaynağı
- P0-25Error codeMotor parameter group selection
- P1-00Error codeMotor type selection
- P1-01Error codeMotor rated power / voltage / current / frequency / speed
- P1-02Error codeMotor rated voltage
- P1-03Error codeMotor rated current
- P1-04Error codeMotor rated frequency
- P1-05Error codeMotor rated speed
- P1-06Error codeEquivalent stator resistance, inductance and rotor inductance of the motor
- P1-07Error codeAsynchronous motor rotor resistance
- P1-08Error codeLeakage inductance of induction motor
- P1-09Error codeMutual inductance of induction motor
- P1-10Error codeNo load current of asynchronous motor
- P1-15Error codeSynchronous motor stator
- P1-16Error codeSynchronous motor D-axis inductance
- P1-17Error codeSynchronous motor Q-axis inductance
- P1-19Error codeSynchronous motor back EMF coefficient
- P1-24Error codeSynchronizer Tuning Failure Alarm Selection (Supported in Version 3750 and above)
- P1-35Error codeSelf learning of motor parameters
- P1-36Error codeAlarm Threshold for VH6-DM100/DC200 Encoder Communication Check Error (Supported in V3750 and above versions)
- P1-37Error codeVH6-DM100/DC200 Encoder Wire Break Alarm Threshold (Supported in V3750 and above versions)
- P1-38Error codeTamagawa Protocol Battery Fault Switch (Supported in V3750 and above versions)
- P1-40Error codeTamagawa Protocol Reset Function (Supported in V3750 and above versions)
- P2Error codeseçim
- P2-00Error codeX1 input terminal function selection
- P3Error codeno under-voltage output) 34: Module temperature reached 35: Warning output (all faults) 37: Running in reverse 39: Output current exceeds the limit 40: Zero-current state 41: The run time has arrived 42: The bus voltage has reached 43: Instant stop and continuous operation function output (Supported in version 3750 and above) 45: STO EDM output (Supported in version 3750 and above) 48: Spindle orientation positioning complete (Supported in version 3750 and above) 49: External pulse positioning complete (Supported in version 3750 and above) 50: External pulse position pulse superposition in progress (Supported in version 3750 and above)