Kawasaki endüstriyel Tüm modeller arıza kodları
Kodlar
- E4534Arıza koduCC-LINK)Parameter setting error. XX
- E4536Arıza koduCC-LINK)Master board is abnormal. XX
- E4537Arıza koduCC-LINK)Initialization error on master board . XX
- E5005Arıza kodu(Spot weld)Weld schedule setting data is abnormal
- E5012Arıza koduCannot change the gun because offset data is abnormal
- E5019Arıza koduWeld fault signal is detected
- E5020Arıza koduRetract pos. monitor error
- E5021Arıza koduExtend pos. monitor error
- E5022Arıza koduCurrent gun retract position differs from a destination
- E5023Arıza koduWear is abnormal, cannot take measurement
- E5026Arıza kodu(Spot welding)RWC error. XX
- E5033Arıza koduCannot weld because of abnormal thickness
- E5039Arıza koduNo response from RWC communication I/F board
- E5043Arıza koduCommunication error in welder. (CodeXX)
- E5046Arıza koduWeld error has arisen
- E5049Arıza koduSerial number signal error
- E5052Arıza koduThe pressurizing power measurement value is abnormal
- E5053Arıza kodu
- E5057Arıza koduInitialization failure in Initialization Weld board
- E5059Arıza koduWelder(DENGEN COMPANY) response error. (welder XX)
- E5062Arıza koduWelder(DENGEN COMPANY) data process error.(welder XX)
- E5063Arıza koduWeld error has arisen. (CodeXX)
- E5065Arıza koduWelder(DENGEN COMPANY) error has arisen. (welder XX)
- E5067Arıza koduMagnet control is abnormal.(welder XX)
- E5522Arıza kodu(Vision)System registered with abnormal data
- E5523Arıza kodu(Vision)Error in processing image(s)
- E5528Arıza kodu(Vision)Image capture error
- E5531Arıza kodu(Vision)Proto data abnormal, so initialized
- E5532Arıza kodu(Vision)Work detection failure
- E5533Arıza kodu(Vision)Initialization error. Code = XX
- E5534Arıza kodu(Vision)Vision system error
- E6011Arıza koduPressure within enclosure is low
- E6018Arıza koduPainting equipment control board error. (CodeXX)
- E6023Arıza kodu(Mutual-Wait)Communication error in Mutual-Wait
- E6025Arıza kodu(Conveyer synchronous communications)It is a conveyer position reception
- E6029Arıza kodu[Servo boardXX]Mismatch in internal pressure in safety circuit
- E6030Arıza kodu[Servo boardXX]Pressure within enclosure is low
- E6032Arıza kodu[Purge control board]Pressure within enclosure is low
- E6033Arıza koduPainting equipment control process error. (CodeXX)
- E6034Arıza koduCartridge table rotate command is abnormal
- E6502Arıza koduArc failure
- E6504Arıza koduArc start failure
- E6505Arıza koduArc weld insulation defect
- E6516Arıza kodu
- E6520Arıza koduLaser sensor tracking value exceeded
- E6521Arıza koduBeyond Laser sensor tracking ability
- E6522Arıza koduLaser sensor cannot detect welding joint
- E6524Arıza koduError in data calculated using Laser sensor
- E6525Arıza koduCannot detect weld joint, Laser sensor tracking set already
- E6526Arıza koduNo response from Laser sensor controller