Omron vücut analiz cihazı All models error codes
Codes
- 2-5Error code3 Communications
- 3-30Error code1 FAILURE ALARM: FAL(006)
- 4-1Error code27 Failure Diagnosis Instructions
- 4-2Error code28 Failure Diagnosis Instructions
- 6-1Error code7 Handling Errors
- 6-2Error code1 Checking Built-in EtherNet/IP Port Error Status
- 6-3Error code1 Error Causes and Remedies
- 6-4Error code1 Error Log
- 10-5Error code22 Serial Communications Instructions
- 11-2Error code5 Error
- A050Error codeA05000 to A05007
- A100Error codeAll
- A202Error codeON when there is a communications port available for automatic allocation. This flag can be used to confirm if all eight communica- tions ports have already been allocated before executing communi- cations instructions
- A203Error codeThese words contain the completion codes for the corresponding port numbers when communications instructions have been exe- cuted. Words A203 to A210 correspond to communications ports 0 to 7
- A213Error codeA21300 to A21307
- A214Error codeEach flag will turn ON for just one cycle after communications have been completed. Bits 00 to 07 correspond to ports 0 to 7. Use the Used Communications Port Number stored in A218 to determine which flag to access. Note: These flags are not effective until the next cycle after the communications instruction is executed. Delay accessing them for at least one cycle
- A215Error codeEach flag will turn ON for just one cycle after a communications error occurs. Bits 00 to 07 correspond to ports 0 to 7. Use the Used Communications Port Number stored in A218 to determine which flag to access. Note: These flags are not effective until the next cycle after the communications instruction is executed. Delay accessing them for at least one cycle
- A216Error codeThe completion code for a communications instruction is automati- cally stored at the address with the I/O memory address given in these words. Place this address into an index register and use indi- rect addressing through the index register to reach the communica- tions completion code
- A218Error codeWhen a communications instruction is executed, the number of the communications port that was used is stored in this word. Values 0000 to 0007 hex correspond to communications ports 0 to 7
- A219Error codeON when an error occurred during execution of a communications instruction. When a flag is ON, check the completion code in A203 to A210 to troubleshoot the error. Turn OFF then execution has been finished normally. Bits 00 to 07 correspond to communications ports 0 to 7
- A260Error codeAll
- A294Error codeThe task number of the current task is written to this word when pro- gram execution is stopped because of a program error. Cyclic tasks have task numbers 0000 to 001F (cyclic tasks 0 to 31). Interrupt tasks have task numbers 8000 to 80FF (interrupt tasks 0 to 255)
- A298Error codeThe current program address is written to these words when program execution is stopped because of a program error. A299 contains the leftmost digits of the program address and A298 contains the rightmost digits of the program address
- A300Error codeError Log Pointer Reset Bit
- A301Error codeAll
- A360Error codeA36001 to A39115
- A394Error codeA39400 to A39407
- A400Error codeAll
- A403Error codeA40300 to A40308
- A404Error codeA40400 to A40407
- A406Error codeAll
- A407Error codeA40700 to A40712
- A408Error codeA40800 to A40807
- A409Error codeA40900 to A40903
- A410Error codeA41000 to A41015
- A411Error codeA41100 to A41615
- A417Error codeA41700 to A41715
- A418Error codeA41800 to A42315
- A426Error codeA42600 to A42611
- A427Error codeA42700 to A42715
- A428Error codeA42800 to A43315
- A444Error codeAll
- A445Error codePulse Output 1 Stop Error Code
- A514Error codeNumber of Power Inter- ruptions
- A518Error codeOperation End Time
- A523Error codeTotal Power ON Time
- A528Error codeA52800 to A52807
- A530Error codeEnabled
- A580Error codeA58000 to A58003
- A5001Error codeFatal error other than FALS