Omron vücut analiz cihazı All models error codes
Codes
- A582Error codeFB DeviceNet Communica- tions Instruction Response Monitoring Time
- A650Error codeA65000 to A65007
- ALS007Error codeGenerates user-defined fatal errors. Fatal errors stop PC operation. Also generates fatal errors with the system. FALS Error Flag ON Execution of Error code written to A400 FALS(007) Error code and time/date written to generates a Error Log Area fatal error with FALS number N. ERR Indicator lit Message displayed on Programming Console
- Bit09Error codeThere is an error in a setting
- Bit13Error codeThe heater current is above 55.0 A
- Bit14Error codeAn input error has occurred
- by1Error codeError Log Pointer
- C101Error codeUser-defined non-fatal errors
- C200HError codeRemote I/O communications refreshing
- CJ1Error codeH/CJ1M/CS1D Only), but the specified error code or
- CJ1MError codeUse the PLC Setup to set the serial communica- tions mode for the RS-232C communications port to Serial PLC Link Polling Unit or Polled Unit. Connect a CJ1W-CIF11 Converter to the built-in RS-232C port to connect multiple CPU Units via RS-422A/485. (RS-232C can also be used for a 1:1 connection.) In this way, up to 10 words of data can be exchanged per CPU Unit
- CJ1WError codeCJ1W-TC004 (2 loops, PNP outputs, HB alarm)
- CJ2Error codeDescribes the following for CJ2 CPU Units: • Overview and features • Basic system configuration • Part nomenclature and functions • Mounting and setting procedure • Remedies for errors • Also refer to the Software User’s Manual (W473)
- CN1Error codeSignal Allocated name CIO word +V OUT0 to Wd m Connect OUT7 or row A circuits Output COM0 indicator Internal +V OUT8 OUto Wd m C oro rn on we c Bt T15 COM0
- CS1Error codeSREAD(639) TB C D TB: First stack address C: Offset value D: Destination word
- CS1DError codeMSKR(692) N D N: Interrupt identifier D: Destination word
- E1Error codeSerial Communications Board (Inner Board) (CS Series only)
- FAL006Error codeGenerates or clears user-defined non-fatal errors. Non-fatal errors do not stop PC operation. Also generates non-fatal errors with the system. FAL Error Flag ON Execution of Corresponding Executed FAL FAL(006) Number Flag ON generates a Error code written to A400 non-fatal error Error code and time written to Error with FAL Log Area number N. ERR Indicator flashes Message displayed on Programming Console
- FPD269Error codeDiagnoses a failure in an instruction block by monitoring the time between execution of FPD(269) and execution of a diagnostic output and finding which input is preventing an output from being turned ON. Time monitoring function: Starts timing when execution condition A goes ON. Generates a non-fatal error if output B isn't turned ON within the monitoring time. Execution condition A T Error-pro- cessing R block (op- tional) Next instruction block Logic diagnosis block* Logic diagnosis execution condition C Diagnostic output B Logic diagnosis function Determines which input in C prevents output B from going ON
- ity51Error codeCurrent consumption Ap
- MBC281Error codeChanges the current EM bank
- MCR260Error codeCalls and executes a communications sequence registered in a Serial Communications Board (CS Series only) or Serial Communications Unit. CPU Unit Serial Communications Unit Port S to R External to device
- O8Error codeOFF
- of8Error codeError occurs in units of 8 points
- or0Error codeInstruction Error Operation
- or16Error code(2) Faulty terminal block connector contact
- PA205RError codeSerial Communications Unit or CPU Bus Unit does not operate or malfunc- tions
- RS-232CError codeD-sub, 9-pin, male
- RXD235Error codeReads the specified number of bytes of data from the RS-232C port built into the CPU Unit or the serial port of a Serial Communications Board (version 1.2 or later)
- SW5Error codeSerial port (RS-232C) communications con- dition: According to CX-Programmer commu- nications settings in PLC Setup. (Refer to Table 1.)
- to511Error codeWord address
- TUP237Error codeChanges the communications parameters of a serial port on the CPU Unit, Serial Communications Unit (CPU Bus Unit), or Serial Communi- cations Board. STUP(237) thus enables the protocol mode to be changed during PLC operation
- TXD236Error codeOutputs the specified number of bytes of data from the RS-232C port built into the CPU Unit or the serial port of a Serial Communications Board (version 1.2 or later)
- XDU255Error codeReads the specified number of bytes of data from the serial port of a Serial Communications Unit (version 1.2 or later). The data is read in no-protocol mode with the start code and end code (if any) specified in the allocated DM Setup Area
- XDU256Error codeOutputs the specified number of bytes of data from the serial port of a Serial Communications Unit (version 1.2 or later). The data is output in no-protocol mode with the start code and end code (if any) specified in the allocated DM Setup Area