Oki atm cihazı All models error codes
Codes
- 001Error codeMachine Check Exception hardware fault detection (board failure or poor power supply)
- 1-1Error codeCable assembly connecting low-voltage power supply unit to SU board (MSU)
- 002Error codeProgram detects the wrong process
- 2-2Error code
- 2-3Error code
- 3-2Error code
- 4-2Error code
- 5-2Error code
- 8-1Error code
- 009Error codeProgram detects the wrong process
- 030Error codeDetect the CU RAM Check error
- 040Error codeDetect the CU EEPROM error
- 054Error codeDetect the communication error between the Controller unit and scanner unit
- 055Error codeController unit cannot detect the scanner unit
- 058Error codeDetect the error at scanner control section 01 : SIP internal error 02 : Scan Model internal error 03 : SPB internal error
- 067Error codeDetect the communication error with the Sleep Mode interface supervisor program
- 069Error codeMalfunction of the NIC chip was detected
- 078Error codeCommunication Error with Operator Panel Unit
- 090Error codeDetect the error at stapler unit
- 122Error codeLow voltage FAN error
- 127Error codeFuser FAN error
- 142Error codeDetected a malfunction of the ID Up/Down mechanism
- 160Error codeToner sensor detection error (160=Y, 161=M, 162=C, 163=K) This error does not occur with the factory default settings
- 161Error codeToner sensor detection error (160=Y, 161=M, 162=C, 163=K) This error does not occur with the factory default settings
- 162Error codeToner sensor detection error (160=Y, 161=M, 162=C, 163=K) This error does not occur with the factory default settings
- 163Error codeToner sensor detection error (160=Y, 161=M, 162=C, 163=K) This error does not occur with the factory default settings
- 980Error codeMedia jamming error around fuser
- 990Error codeWaste toner sensor detection error
- all001Error codeMachine Check Exception hardware problem was detected (PCB failure or insufficient power capacity) (PDL only) When CE1 was not detected, SC001 occurs
- all020Error codeThe CU FW in Nand FLASH has not been detected or a check SUM error has occurred
- all024Error codeCU Font ROM Hash Error
- all025Error codeDetected a Font ROM DIMM _ hash check error. (Japan Model only)
- all030Error codeCU RAM Check Error
- all031Error codeIs the applicable RAM DIMM mounted properly? Is operation restored by replacing the applicable RAM DIMM?
- all032Error codeIs the applicable RAM DIMM mounted properly? Is operation restored by replacing the applicable RAM DIMM?
- all036Error codeIs this a standard RAM DIMM? Is the applicable RAM DIMM difference mounted normal? Is operation restored by replacing the applicable RAM DIMM?
- all037Error codeIs this a standard RAM DIMM? Is the applicable RAM DIMM difference mounted normal? Is operation restored by replacing the applicable RAM DIMM?
- all040Error codeCU EEPROM Error
- all041Error codeIs the error display reproducible?
- all042Error codeFailed to access flash memory that is surface- mounted on CU PCB
- all050Error codeIs the error display reproduc- ible?
- all051Error codeCU Fan Error Abnormal condition of the CPU cooling fan on the CU PCB
- all052Error codeIs the error display reproducible?
- all060Error codeIs the error display reproducible?
- all062Error codeIs the error display reproducible? Is the Network PCB properly mounted?
- all063Error codeDoes replacement of the network PCB correct the problem?
- all067Error codeA communication error was detected during communication with the Sleep Mode interface monitoring program
- all069Error codeMalfunction of the NIC chip was detected
- all072Error codeIs the CU Assy properly mounted? Does replacement of the CU PCB correct the problem?
- all073Error codeIs the CU Assy properly mounted? Does replacement of the CU PCB correct the problem?