Oki atm cihazı All models error codes
Codes
- all081Error code
- all096Error codeIs the error display reproducible?
- all097Error codeIs the error display reproducible?
- all102Error codeDoes the Error take place again?
- all103Error codeDoes the Error take place again?
- all104Error codeThe engine EEPROM implementation check at power on showed no problem, but after that a read/write error was detected
- all105Error codeIs there an EEPROM? Does the Error take place again?
- all106Error codeAbnormal engine control logic
- all108Error code01: Detection of a watchdog timer error
- all121Error codeHigh Voltage power supply interface error
- all123Error codeAbnormal environment humidity or unconnected humidity sensor
- all124Error codeAbnormal environment humidity
- all125Error codeMulti-purpose Tray Home Error
- all127Error code1) Is the fuser cooling fan operating? 2) Cooling fan is replaced but Error occurs again
- all131Error code1) Is an Error message displayed? 2) Is the LED head properly mounted? 3) Does the Error take place again?
- all134Error codeLED head detection error (01=K, 02=C, 03=M, 04=Y, 05=W/CL)
- all135Error code01: Tray 1 Lift-up Motor Error 02: Tray 2 Lift-up Motor Error 03: Tray 3 Lift-up Motor Error 04: Tray 4 Lift-up Motor Error 05: Tray 5 Lift-up Motor Error
- all142Error code1) Is an Error message displayed? 2) Does the Error take place again?
- all143Error codeImage drum Up/Down position detection error (01=K, 02=C, 03=M, 04=Y, 05=W/CL)
- all144Error code1) Is the toner lock-lever- open error indicated? 2) Does the problem persist even if the ID units are replaced?
- all147Error codeToner supply motor error (01=K, 02=C, 03=M, 04=Y, 05=W/CL)
- all154Error codeIs the belt unit mounted normally?
- all155Error codeIs the fuser unit mounted normally?
- all160Error code1) Is an Error message displayed? 2) Does the Error take place again?
- all163Error codeToner sensor detection error (01=K, 02=C, 03=M, 04=Y, 05=W/CL) This error does not occur with the factory default settings
- all166Error codeAn abnormality was detected with the power supply temperature thermistor. 01: The power supply thermistor is detected as shorted. 02: The power supply thermistor is detected as open. 03: The power supply thermistor indicates high temperature error 04: The power supply thermistor indicates low temperature error
- all167Error codeThermistor slope error
- all168Error code01: Thermistor is detected as shorted 02: Thermistor is detected as open 03: Thermistor is indicates high temperature error 04: Thermistor indicates low temperature error
- all169Error code01: Thermistor is detected as shorted 02: Thermistor is detected as open 03: Thermistor is indicates high temperature error 04: Thermistor indicates low temperature error
- all170Error codeShort circuit (170) or open circuit (171) of the fuser thermistor was detected
- all172Error codeAn abnormal (172: high or 173: low) temperature of the fuser thermistor was detected
- all173Error code1) Is an Error message displayed? 2) Does the Error take place again?
- all179Error code1) Is the model and power voltage of the fuser mounted proper? 2) Fuser is properly mounted, but Error results again
- all180Error code1) Is an Error message displayed? 2) Does the Error take place again?
- all181Error codeOption unit I/F error (181 = Duplex Unit. 182, 183, 184, 185 = Optional Tray)
- all187Error codeIs the control panel and cable connected properly?
- all188Error code01: Error in communication with Port CPU
- all189Error code1) Inverter communications error 2) Does the Error take place again?
- all190Error codeSystem Memory Overflow
- all200Error codeError occurred when downloading PU firmware
- all230Error codeTag Reader Missing
- all231Error code01: PU-Tag Reader Interface Error 02: Tag Reader circuit abnormality 03: Tag Interface error
- all240Error code240: Flash-memory hardware error 241: Duplex flash-memory error 242: Optional tray-2 flash-memory error 243: Optional tray-3 flash-memory error 244: Optional tray-4 flash-memory error 245: Optional tray-5 flash-memory error 247: Sub-CPU flash-memory error 248: Inverter flash-memory error
- all241Error codeEngine Program Memory Error 241: DUPLEX Flash memory error 242: Option Tray 2 243: Option Tray 3 244: Option Tray 4 245: Option Tray 5
- all247Error codeEngine PORT CPU Program Memory Error
- all249Error codeEngine DRIVER CPU Program Memory Error
- all251Error codeSecure Disk Erasing Error
- all254Error codeAn unexpected error occurred during initialization of the Security mode. Error cause information is displayed after the error code number
- all257Error codeAn unexpected error occurred during initialization of the HDD Error cause information is displayed after the error code number
- all260Error codeHeater thermistor error