Lincoln Electric All models error codes
Codes
- C201Error codeMETER CIRCUIT C401 500 MFD C402 4.7 MFD C403 27 MFD CC 44 00 64 } .022 MFD C407 TD H4 R01 U } 1A D404 X401 VOLTAGE REGULATOR DM401 DIGITAL METER R401 24.3K OHM 1/4W 1% R402 2K OHM TRIMMER R403 2.80K OHM 1/4W 1% R406 7.68K OHM 1/4W 1% R407 1K OHM TRIMMER R408 102K OHM 1/4W 1% R409 10K OHM TRIMMER T FOR VOLTMETER P.C. BOARDS C L S6 C6 H8 E7 M-1 A TO IR C H FOIG RH CER O MU PS OE NS E2 N1 T145 D T VALUES AND CIRCUIT CONNECTIONS. D D D
- CO2Error codeCO2 besleme soketi ısıtıcı bağlantı kiti
- EM7130Error codeMOBIFLEX® 100-NF PORTABLE FAN
- EM7940Error codeCKS - BAĞLANTI KİTİ
- EM9850Error codeNCW 4 - BAĞLANTI TELİ, 4M
- F101Error codeThe field fuse (F101), located on the power PC board, repeatedly fails
- i14Error codeDİJİTAL ARCLINK/LINC-NET KONTROL KABLOLARI
- K1034Error codeKONTROL KABLOSU HS 5 m
- K1039Error codeUzatma kablosu, 15 m
- K1400Error codeCO2 besleme soketi ısıtıcı bağlantı kiti
- K1405Error codeHYPERFILL GAZ DAĞITICI, 2 ADET
- K1416Error codeUzatma Kaynak Kablosu 70 mm2
- K1417Error codeGaz akış ölçer kiti
- K1419Error codeKONTROL KABLOSU, 5M
- K1420Error codeKablo askı aparatı
- K6902Error code9 TO 14-PIN KONTROL KABLOSU, 20M
- KP52Error codeGAZ DAĞITICISI, 0.9-1.2 MM
- LN-8Error code2. On cables with more than one electrode cable, leave the junction between the two or more cables and the single 4/0 stub behind the clamp so only the single electrode lead is under the clamp. 3. Pass the single electrode cable through the holes provided in the back corner of the control section and fasten it to the tab on the conductor above the rear brass block of the wire feeder. LN-8NE AND LN-8SE The extension unit consists of a wire reel mount with a hand crank and either a 22-1/2 or 45 ft (6.9 or 13.7 m) extension cable assembly. The cable is rated at 450 amps, 50% duty cycle. The extension cable can be used for 0.068 through 0.120 in. (1.7 through 3.0 mm) flux-cored electrode and 5/64 through 3/32 in. (2.0 through 2.4 mm) solid electrode. The 22-1/2 ft. (6.9 m) cables can also be used for 1/16 in. (1.6 mm) solid electrodes. To con- nect the cables, perform these steps: 1. When shipped, the hand crank on the wire reel mount is equipped to
- LN-9Error codeThe LN-9 shuts down while weld- ing. Upon retriggering, the gun the unit will weld again for a period of time
- osu10Error codeGüç Kablosu 10.6m - 600A/%60
- osu18Error codeGüç Kablosu 18.3m - 600A/%60
- osu33Error codeGüç Kablosu 33.5m - 600A/%60
- osu70Error codeUzatma Kaynak Kablosu 70 mm2
- osu95Error codeUzatma Kaynak Kablosu 95 mm2
- R4Error codeInput voltage before the circuit breaker and 2 ohm resistor (R4)
- S2Error codeWith the interlock switch (S2) in the “ON” postion, the wire feed stops when the gun trigger is released
- W0002Error codeTIG torcu - 135A - 4m, valf, 9 mm
- W0003Error codeSU AKIŞ SENSÖRÜ**
- W1052Error codeTIG torcu - 135A - 4m, valf, 13 mm
- W8800Error codeFiltre Kartuşu
- wer500Error codeThe arc voltage appears to rise too slowly or stubs or blasts at the start of a weld. Once started the weld- ing is good. NOTE: Pulse Power 500 operation with a filter kit may exhibit these symptoms