Hitachi kan ışınlama cihazı Tips give a special instruction that can error codes
Codes
- B052Error codeKontrollü yavaşlama fonksiyonu için aşırı voltaj eşiğini ayarlar. Aralık 0,0 ila 1000V'dir.
- B088Error codeFRS'den sonra modu yeniden başlat
- B091Error codeSelects how the inverter stops the motor, two option codes: 00 DEC (decelerate and stop) 01 FRS (free run to stop)
- B092Error codeİki seçenek kodu: 00 Fan her zaman açık 01 Çalışma sırasında FAN açık, DURDURMA sırasında KAPALI
- B101Error codeSerbest ayar V/f voltajı (1)
- B103Error codeSerbest ayar V/f voltajı (2)
- B105Error codeSerbest ayar V/f voltajı (3)
- B107Error codeSerbest ayar V/f voltajı (4)
- B109Error codeSerbest ayar V/f voltajı (5)
- B111Error codeSerbest ayar V/f voltajı (6)
- B113Error codeSerbest ayar V/f voltajı (7)
- B124Error codeFren serbest bırakmayı açtıktan/KAPATTIKTAN sonra onaylama için bekleme süresini ayarlar. Belirtilen bekleme süresi boyunca onay alınmazsa, invertör harici bir fren hatası ile açılır. Aralık 0,00 ila 5,00 sn'dir
- B126Error codeFren serbest bırakma sinyalinin izin verileceği minimum invertör akım seviyesini ayarlar. Aralık, nominal akımın % 0 ila % 200 'üdür
- B212Error codeLevel of electronic thermal setting, 2nd motor
- B213Error codeElectronic thermal characteristic, 2nd motor
- B312Error codeLevel of electronic thermal setting, 3rd motor
- B313Error codeElectronic thermal characteristic, 3rd motor
- C026Error codeAlarm rölesi terminal fonksiyonu
- C036Error codeAlarm rölesi terminali aktif durumu
- C040Error codeAşırı yük sinyali çıkış modu
- C041Error codeAşırı yük seviyesi ayarı 1
- C044Error codeAkıllı çıkışı [OD] tetiklemek için PID döngüsü hata eşiğini |SP - PV| (mutlak değer) ayarlar. Aralık % 0,0 ila % 100, çözünürlük % 0,1 'dir
- C062Error codeİkili alarm kodlarının akıllı terminallere gönderilmesini sağlar. Üç seçenek kodu: 00 Devre Dışı Bırak 01 Etkinleştir - 3 bit kod 02 Etkinleştir - 4 bit kod
- C071Error codeİletişim hızı seçimi
- C073Error codeİletişim veri uzunluğu seçimi
- C074Error codeCommunication parity selection
- C075Error codeCommunication stop bit selection
- C078Error codeCommunication wait time
- C111Error codeRange is 0.00 times rated current to 2.00 times rated current
- D001Error codeReal-time display of output frequency to motor, from 0.0 to 400.0 Hz
- D002Error codeFiltered display of output current to motor (100 mS internal filter time constant)
- D013Error codeVoltage of output to motor, range is 0.0 to 600.0V
- D090Error codeProgramlama hata kodunu görüntüler
- E01Error codeThe inverter output was short-circuited, or the motor shaft is locked or has a heavy load. These conditions cause excessive current for the inverter, so the inverter output is turned OFF. The dual-voltage motor is wired incorrectly. Note: The SJ300 will over current trip at nominally 200% of rated current for models up to -550xxx; nominally 180% of rated current for models -750xxx to -1500xxx
- E02Error codeOver current event during deceleration
- E03Error codeOver current event during acceleration
- E04Error codeDC braking power(A054) is set too high, or a current transformer error occurred, or a noise source induced the error
- E05Error codeWhen a motor overload is detected by the electronic thermal function, the inverter trips and turns OFF its output
- E06Error codeWhen the regenerative braking resistor exceeds the usage time allowance or usage ratio, the inverter trips and turns OFF its output to the motor
- E07Error codeWhen the DC bus voltage exceeds a threshold, due to regenerative energy from the motor
- E08Error codeWhen the built-in EEPROM memory has problems due to noise or excessive temperature, the inverter trips and turns OFF its output to the motor
- E09Error codeA decrease of internal DC bus voltage below a threshold results in a control circuit fault. This condition can also generate excessive motor heat or cause low torque. The inverter trips and turns OFF its output
- E10Error codeIf a strong source of electrical interference is close to the inverter or a fault occurs in a built-in CT (current transformer), the inverter trips and turns its output OFF
- E11Error codeA malfunction in the built-in CPU has occurred, so the inverter trips and turns OFF its output to the motor
- E12Error codeA signal on an intelligent input terminal config- ured as EXT has occurred. The inverter trips and turns OFF the output to the motor
- E13Error codeWhen the Unattended Start Protection (USP) is enabled, an error occurred when power is applied while a Run signal is present. The inverter trips and does not go into Run Mode until the error is cleared
- E14Error codeThe inverter is protected by the detection of ground faults between the inverter output and the motor during powerup tests. This feature protects the inverter, and does not protect humans
- E15Error codeWhen the input voltage is higher than the specified value, it is detected 60 seconds after powerup and the inverter trips and turns OFF its output
- E16Error codeWhen the input power is removed for more than 15ms, the inverter trips and the output to the motor turns OFF. If the power failure duration exceeds the duration set in parameter B002, it is consid- ered a power failure. When input power is restored, the inverter restarts if the Run signal is present, depending on the restart condition
- E21Error codeWhen the inverter internal temperature is above the threshold, the thermal sensor in the inverter module detects the excessive temperature of the power devices and trips, turning the inverter output OFF