Hamilton Medical All models error codes
Codes
- 40Error codeThere is an emergency alarm 40 seconds after switching on GALILEO Gold. The display does not show the setup screen. The green LED named Access 1+2 (Figure 12-1 on page 12-59) is either always on, or always off
- a2Error codeCO2 sensor/adapter calibration (main- stream/ sidestream)
- ADC10Error codeAnalog-digital channel 10. Displays the voltage of the analog signal to the expiratory valve
- ADC11Error codeA/D Channel 11 - voltage of the (nominal) 15 VDC power (half the actual value)
- ADC12Error codeAnalog-digital channel 12. Displays the voltage supplied to the CompactFlash card. This is nominally 12 V. However, because of display limitations, the value shown on screen is half of the real value supplied
- ADC13Error codeAnalog-digital channel 13. Displays the voltage from the temperature measurement resistor
- ADC14Error codeAnalog-digital channel 14. Displays the value of the (nominal) -10 V supply to the pressure sensors
- ADC15Error codeAnalog-digital channel 15. Displays the value of the (nominal) 10 V power supply to the inspiratory (servo) valve
- ADC16Error codeAnalog-digital channel 16. Displays the ground voltage
- ARM100Error codePaux NEBULIZER FLOW SENSOR ALARM 100
- ASV47Error codeAdult/Ped
- C1Error codeProvides setup and use information for the INTELLiVENT-ASV ventilation mode.2,3 The current version of the manual for software version 3.0.x also applies to software version 3.1.x
- CO2Error codeHAMILTON MEDICAL CAPNOSTAT 5TM sensor
- E-24Error codeSensor board on page E-24
- E1Error codeRatio of inspiratory time to expiratory time. Applies to mandatory breaths, if the ventilator is so configured
- ery20Error codeVentilator
- esi119Error codeSes basıncı seviyesi119
- ess160Error codeAlarm volume (Loud- ness160)
- eti118Error codeAlarm ses düzeyi (Şiddeti118)
- G-1Error codeHAMILTON LoFlow™ sidestream CO2 sensor
- H-1Error codeCable, serial connector to computer, 2.5 m (8.2 ft). Shielded on male (ventilator) side only1
- H-2Error codePhilips Open VueLink Philips-specific standard protocol for transmitting data, offers preconfigured data mapping
- han10Error codePressure gauge reads higher than 10 mbar with old type valve, or hig than 4 mbar with new type. (Leaka is too high.)
- hin20Error code
- i1Error codeBasınç
- IBW45Error codeIdeal body weight. A calculated value using height and sex, used in calculations for ASV and startup ventilation settings for adult and pediatric patients
- IE6060Error code
- IEC61Error code3 Vrms 150 kHz to 80 MHz outside ISM bands2 10 Vrms 150 kHz to 80 MHz in ISM bands4
- igh45Error codeWhen Sigh is activated, every 50th breath is applied using one of the following settings: = In pressure-controlled modes, the pressure delivered is > 10 cmH2O above the currently set Pcontrol or Pinsp. = In volume-controlled modes, the tidal volume delivered is 150% of the current tidal volume (Vt) setting. During Sigh breaths, the Pressure and Vt alarm limits remain in effect to help protect the patient from excessive pressures and volumes. Not available for neonatal patients, in DuoPAP or APRV modes, or with HiFlowO2
- igh79Error code
- ion10Error codeThis section gives an overview of the alarm indications
- IP21Error codeSu damlacıklarına ve 12,5 mm'den büyük katı parçacıklara karşı koruma- lıdır
- let104Error codePressure
- lve81Error code
- nce100Error code
- no2Error code
- O2Error codeO2 cell cal. needed (or your local language equivalent) is displayed. The calibration was not successful
- of16Error codeThe LCD display The group of 16 does not show the LEDs is not GALILEO setup flashing (check screen. (The especially LED 15 self-test screen on the bottom displays right). Self-Test: followed by a status bar.)
- P0Error codeNOTE: Due to changes in pneumatic impedance, P0.1 values may vary with different settings of the Trigger func- tion. Airway occlusion pressure. The maximal slope of the airway pressure drop during the first 100 ms when the airway is occluded. P0.1 indicates the patient’s respiratory drive and efforts. It applies to patient-triggered breaths with pressure trigger only. A P0.1 value of -3 cmH2O indicates a strong inspiratory effort, and a value of -5 cmH2O, an excessive effort, possibly because the patient is “air hungry" (peak inspiratory flow or total ventilatory support is inadequate) or has an excessive drive. If P0.1 is below -3 cmH2O...
- P2Error code
- P49Error codeSürücü Basınç aşağıdaki gibi hesaplanır: ΔP = Pplato - (PEEP + OtoPEEP)
- PA12Error codeSteam autoclave, chemically disinfect, or ETO sterilize For details about reprocess- ing the autoclavable expira- tory valve, see Section 10.6
- PN1551Error codeInspiratory valve PN 155491 (New type)
- PN6243Error codeProvides information about installing and setting up the medical equipment, as well as additional tech- nical and servicing information for the ventilator
- PN6270Error codeThe current version of the manual for software version 3.0.x also applies to software version 3.1.x
- QO2Error codeOxygen Flow Sensor
- RS-232Error codeSend monitored data, ventilator settings, and alarms to a patient monitor, a patient data management system (PDMS), or other computer system. See Section H.3
- s50mError codeDisplays the flow to the patient in milliliters per second, as measured at the inspiratory valve
- s100mError codeDisplays patient pressure: a measurement of the pressure in the patient breathing circuit as measured at the inspiratory valve
- SA6049Error codeCircuit diagram of the sensor board