Xerox All models error codes
Codes
- 8-1Error codeXerographic Drive Motor and Erase Lamp (The Service Manual makes it appear that the code 4-1 tests the same components)
- 8-6Error codeRegistration Sensor
- 8-8Error codeRegistration Gate Sensor
- 8-10Error codeBypass Size Sensor
- 8-16Error codeHigh Capacity Feed Elevator Motor
- 8-20Error codePaper Path Drive Motor
- 8-21Error codeHigh Capacity Feeder Feed Motor
- 8-50Error codeDuplex Drive Motor (low speed)
- 8-51Error codeDuplex Drive Motor (high speed)
- 8-52Error codeDuplex Inverter Sensor
- 8-56Error codeDuplex Module Entrance Sensor
- 8-68Error codeDuplex Side Guide Motor (forward
- 8-69Error codeDuplex Side Guide Motor (reverse)
- 8-70Error codeDuplex Side Guide Sensor
- 9-1Error codeXerographic Drive Motor and Erase Lamp (this is the third code which seems to be identical to the other two (8-1 & 4-1)
- 9-5Error codeHVPS/Main Drive Motor
- 9-7Error codeToner Sensor (Front Door must be closed)
- 9-9Error codeLow Toner Sensor
- AError codeFeed Motor 2 (or 3) activating signal
- ACError codeAlternating Current
- BError codeFeed Motor 2 (or 3) activating signal
- C1Error code0: Tray 1 fed paper did not actuate Tray 1 Takeaway Sensor in time after Tray 1 feed motor
- C2Error code0: Tray 2 fed paper did not actuate Tray 2 Takeaway Sensor in time after Tray 2 Feed Motor
- C3Error code0: Bypass fed paper did not actuate IOT Registration Sensor in time after Bypass Feed
- C4-1Error codeTray 1 fed paper did not actuate Registration Sensor in time
- C4-2Error codeTray 2 fed paper did not actuate Registration Sensor in time
- C4-3Error codeTray 1 fed paper actuated Registration Sensor too early after Tray 1 Feed Motor is ener-
- C4-4Error codeTray 2 fed paper actuated Registration Sensor too early after Tray 2 Feed Motor is ener-
- C4-5Error codeTwo-side fed paper did not actuate Registration Sensor in time
- C4-6Error codeTwo-side fed paper actuated Registration Sensor too early
- C5Error code0: Tray 1 No Paper Sensor is not actuated
- C6Error code0: Tray 2 No Paper Sensor is not actuated
- CN2Error codeF-42
- CR1Error codeIndicates that a power on diagnostics failure has occurred when flash
- DCError codeDirect Current
- ENS1Error codeSignal from the Low Paper Sensor. Goes Low when Paper is low in the Paper Tray
- H1-4Error codeHCF (Tray 5) Elevator Lift problem - Upper Limit Sensor is not actuated
- H2-1Error codeDuplex (Tray 4) Communication problem
- H2-2Error codeDuplex (Tray 4) Side Guide positioning failure
- H6-1Error codeDADF Width Sensor actuated at power on (DADF Reg sensor not actuated)
- H6-2Error codeADF or DADF Nudger Roll Positioning Failure
- H6-3Error codeDADF Belt Drive Motor lost the 24v line
- H6-4Error codeDADF to Main Board Communication failure
- ith2000Error codeE2-D
- J508Error codeConnects the Duplex Motor to the Duplex PWB
- J509Error codeConnects the Duplex Motor
- J510Error codeConnects the Exit Motor to the Duplex PWB
- J511Error codeConnector Inside the Exit Motor
- J513Error codeConnects the SNS Harness to the Duplex Sensor
- J515Error codeConnects the Offset Motor Assembly to the OCT PWB