Tren All models error codes
Codes
- 1Error codeCalibration Belt Tension
- 10Error codeLine Frequency Out Of Acceptable Range
- 11Error codeLow Voltage Watchdog (Upper PCA1
- 12Error codeMC2 / LPCA3 Software Watchdog (Lower PCA4)
- 14Error codeFan Fail (Lower PCA1)
- 15Error codeDC2 Bus Over Voltage
- 16Error codeAC3 Input Voltage Too Low
- 21Error codetoo Many Maximum Consecutive Power Requests
- 22Error codeError 22 indicates that the drive motor has been instructed to start, by either manual or program control, and the monitoring system has not received any response from the speed sensing system indicating that the drive motor has started
- 23Error codeError 23 indicates that the speed sensor signal was lost while the tread- mill was in operation
- 25Error codeMotor Controller / LPCA1 Hardware Error
- 26Error codeError 26 monitors the speed sensor signal and verifies the speed sensor signal is appropriate for the requested speed. If the speed sensor signal is incorrect or erratic an Error 26 will be displayed
- 28Error codeElectronics Temperature Too High
- 29Error codeExcessive AC2 Input Current
- 30Error codeError 30 is defined as upper PCA is active, the lower PCA is not com- municating
- 31Error codeError 31 is defined as faulty data received from lower PCA (extremely rare)
- 32Error codeError 32 is defined as lower PCA is active, the upper PCA is not com- municating
- 33Error codeError 33 is defined as faulty data received from upper PCA (extremely rare)
- 37Error codeE-STOP Upper PCA2/Lower PCA3 Mismatch
- 40Error codeNo Lift Motion Detected
- 42Error codeLift Position Out Of Range
- 44Error codeUn-commanded Lift Motion
- 45Error codeLift Moving In the Wrong Direction
- 65Error codeInformation Display
- 80Error codeError 80 - Incline (or crossramp) will stop at current incline. Error 80 is dis- played when there is a missing incline signal on pins 1 or 2. Restart is not needed to clear the error, self-recovery possible when the control is returned to the center position
- 81Error codeError 81 - Incline (or crossramp) will stop at current incline. Error 81 is dis- played when there is a missing incline signal on pin 3. Restart is not needed to clear the error, self-recovery possible when the control is returned to the center position
- 82Error codeError 82 - Speed will decrease at 0.1 mph per key press until belt stops. Error 82 is displayed when there is a missing drive signal on pins 6 or 7. Restart is not needed to clear the error, self-recovery possible when the control is returned to the center position
- 83Error codeError 83 - Speed will remain at current speed. Error 83 is displayed when there is a missing drive signal on pin 8. Restart is not needed to clear the error, self-recovery possible when the control is returned to the center position
- E0Error codeEEPROM kontrol hatası
- E1Error codeİç / dış ünite iletişim hatası
- E2Error codeİç ünite serpantin donma sensörü devreye girdi
- E3Error codeODU Coil temperature sensor failure. (OPT)
- E4Error codeYüksek basınç koruması
- E5Error codeKompresörde aşırı akım
- E6Error codeabnormal（IDU failure）
- E7Error codeODU Ambient Temperature sensor failure
- E8Error codeODU Discharge Temperature sensor failure
- E9Error codeIPM / Compressor driving control abnormal
- EEError codeODU EEPROM failure
- EED1Error codeUse the SPEED numeric 1 & 2 keys to scroll up and down through the current menu
- F0Error code（IDU failure）
- F1Error codeDischarge temperature sensor failure
- F3Error codeODU coil temperature failure PROTECTION
- INE0Error codeSelects the current menu item or confirms settings
- OKError codeSelects the current menu item or confirms settings
- P0Error code1. ODU PCB broken? 2. Power supply abnormal?
- P1Error codeOver / under voltage protection
- P2Error codeOver current protection
- P6Error codeOverheating protection on Cooling mode
- P7Error codeOverheating protection on Heating mode