Panasonic PHC kan bankası buzdolabı All models error codes
Codes
- 1-99Error codePotwierdź ustawienia temperatur suszenia betonu dla poszczególnych etapów
- a1Error code• Dopo aver selezionato il sistema a 1 o 2 zone, procedere alla selezione della stanza o della piscina. • Se si seleziona la piscina, la temperatura deve essere selezionata con un T tra 0 °C e 10 °C
- DT9000Error codeThe self-diagnostic error code is stored here when a self-diagnostic error occurs. Monitor the error code using decimal display
- DT9001Error codeThe position of the I/O for which an error occurred is stored in bits 0 to 3
- DT9002Error codeThe current scan time is stored here. Scan time is calculated using the formula: Scan time (ms) = stored data (decimal) x 0.1 K50 indicates 5 ms
- DT9005Error code- Tool port bit 0=1: Over run error bit 1=1: Framing error bit 2=1: Parity error - RS232C port bit 8=1: Over run error bit 9=1: Framing error bit 10=1: Parity error
- E1Error codeA program with a syntax error has been written. ⇒ Change to PROG. mode and correct the error
- E2Error codeTwo or more OT(Out) instructions and KP(Keep) instructions are programmed using the same relay.Also occurs when using the same timer/counter number. ⇒ Change to PROG. mode and correct the program so that one relay is not used for two or more OT instructions,Or, set the duplicated output to “enable” in system register20. A timer/counter instructon double definition error will be detected even if double output permission has been selected
- E20Error codeProbably a hardware abnormality ⇒Please contact your dealer
- E21Error codeProbably an abnormality in the internal RAM. ⇒Please contact your dealer
- E22Error codeRAM error2
- E23Error codeRAM error3
- E24Error codeRAM error4
- E25Error codeRAM error5
- E26Error codeFP-X: When the master memory cassette is mounted, the master memor cassette may be damaged. Remove the master memory, and check whether the ERROR turns off. When the ERROR turned off, rewrite the master memory as its contents are damaged, and use it again. When the ERROR does not turn off, please contact your dealer
- E28Error codeProbably an abnormality in the system register. ⇒ Check the system register setting or initialize the system registers
- E29Error codeA parameter error was detected in the MEWNET-W2 configuration area. Set a correct parameter
- E30Error codeProbably a hardware abnormality. ⇒ Please contact your dealer
- E31Error codeAn interrupt occurred without an interrupt request . A hardware problem or error due to noise is possible. ⇒ Turn off the power and check the noise conditions
- E33Error codeThis error occurs when a FP3/FP10SH is used as CPU2 for a multi-CPU system. ⇒Refer to “Multi-CPU system Manual”
- E39ParameterWhen reading in the program from the IC memory card(due to automatic reading because of the dip switch setting or program switching due to F14(PGRD) instruction): - IC memory card is not installed. - There is no program file or it is damaged. - Writing is disabled. - There is an abnormality in the AUTOEXEC.SPG file. - Program size stored on the card is larger than the capacity of the CPU. ⇒Install an IC memory card that has the program proterly recorded and execute the read once again
- E40Error codeMEWNET-TR communication error FP3 and FP10SH: Check the contents of special data registers(FP3:DT9002,DT9003,FP10SH:DT9 0002,DT90003) and the erroneous master unit and abnormal I/O unit. Then check the unit. Selection of operation status using system register21: -to continue operation,set 1 -to stop operation,set 0 Verification is possible in FPWIN GR/Pro at”I/O error” in the status display function
- E45Error codeOperation became impossible when a high- level instruction was executed. Selection of operation status using system register26: -to continue operation,set K1 -to stop operation,set K0 The address of operation error can be confirmed in either special data registers DT9017 and DT9018, or DT90017 and DT90018. (It varies according to the model to be used.) DT9017, DT9018: FP-e, FP0, FP0R(FP0 mode) DT90017, DT90018: FP∑, FP-X, FP0R(FP0R mode), FP2, FP2SH, FP10SH Verification is possible in FPWIN GR/Pro at”I/O error” in the status display function
- E46Error codeS-LINK error Occurs only in FP0-SL1 When one of the S-LINK errors (ERR1, 3 or 4) has been deteced,error code E46 (remote I/O (S-LINK) communication error) is stored. Selection of operation status using system register27: -to continue operation,set K1 -to stop operation,set K0
- E47Error codeIn the unit on the slave station, an abnormallty such as: -missing unit -abnormal intelligent unit was detected. FP2, FP2SH, and FP10SH: Check the contents of special data registers DT90131 to DT90137 and locate the abnormal slave station and recover the slave condition. FP3: Check the contents of special data registers DT9131 to DT9137 and locate the abnormal slave station and recover the slave condition. Selection of operation status using system register28: -to continue operation,set 1 -to stop operation,set 0
- E50Error codeThe voltage of the backup battery lowered or the backup battery of conrol unit is not installed. By setting the system register 4, you can disregard this self-diagnostic error
- E52Error codeSet the INITIALIZE/TEST selecto1inmjvbgycfrde892 r to the INITIALIZE position while keeping the mode selector in the RUN position.If the same error occurs after this,please contact your dealer
- E53Error codeAbnormality was detected when the multi- CPU system ws used. Please contact your dealer
- E54Error codeThe voltage of the backup battery for the IC memory card lowered. The BATT.LED does not turn on.
- E55Error codeThe voltage of the backup battery for IC memory card lowers.The BATT.LED does not turn on. (The contents of the IC memory card cannot be guaranteed.)
- E57Error codeMEWNET-W2/MCU The MEWNET-W2 link unit or MCU(Multi communication unit) is not installed in the slot specified using the configuration data. Either install a unit in the specified slot or change the parameter
- E100Error codeThe error specified by the F148 (ERR)/P148(PERR) instruction is occurred. ⇒ Take steps to clear the error condition according to the specification you chose
- F12Error codeDrukschakelaar geactiveerd
- F14Error codeNedostatečné otáčky kompresörü
- F15Error codeFout vergrendeling ventilatormotor
- F16Error codeStörung wg. überhöhter Stromaufnahme
- F20Error codeOchrana před přetížením kompresörü
- F22Error codeProtection surcharge transistor module
- F23Error codeStörung wg. Gleichstromspitzen im AG
- F24Error codeFout koelcyclus
- F25Error code*1, *2 Fout koel- / verwarmingscyclus
- F27Error codeFout drukschakelaar
- F30Error codeFout sensor 2 wateruitlaat
- F32Error codeFout interne thermostaat
- F36Error codeFout sensor omgevingstemp. buiten
- F37Error codeFout sensor waterinlaat
- F40Error codeFout sensor afvoer buiten
- F41Error codeFout correctie vermogensfactor
- F148Error codeStores the self-diagnostic error number “n” in (DT9000), turns R9000 on, and turns on the ERROR LED
- F356Error codeTemperature control (PID) can be easily performed using the image of a temperautre controller