Nokia switch All models error codes
Codes
- 8Error codeSP-%c RS232 craft interface failure
- 75Error codeIndicates a module that was provisioned but is autonomously out of service. IOM may be faulted or missing
- 77Error codeIndicates the IOM did pass diagnostics but failed to take configuration commands from the System Processor. Software Version mis-onfiguration, corrupt software image or faulted hardware on the IOM
- 78Error codeAlarm cutoff button pressed
- 82Error codeIOM-%d Failed to burn prom partition %s error %d
- 84Error codeIndicates programming the flash on the IOM exceeded the allotted time. Faulted IOM
- 85Error codeIOM-%d kernel fault
- 86Error codeIOM-%d process %s - abnormally ended
- 89Error codeSP-%c cpu threshold alarm cleared
- 742Error codeMemory allocation for bit map failed. Not provisioned or software or CPU subsystem error
- 743Error codeMemory allocation for TCSAP failed. Not provisioned or software or CPU subsystem error
- 745Error codeThis alarm is obsolete. Indicates a software error
- 750Error codeIndicates a software error. Corrupted disk file system or software or CPU subsystem error
- 751Error codeIndicates a software error. Corrupted disk file system or software or CPU subsystem error
- 767Error codeSAP configuration before general. Not provisioned or software or CPU subsystem error
- 769Error codeTCSAP configuration before general. Not provisioned or software or CPU subsystem error
- 783Error codeIndicates a software error. Corrupted disk file system or software or CPU subsystem error
- 784Error codeIndicates a software error. Corrupted disk file system or software or CPU subsystem error
- 787Error codeSCPI - Encoding error
- 788Error codeSCPI - Decoding error
- 793Error codeIOM-%d-%s Cell transmission failure - APC to TADM
- 794Error codeIOM-%d-%s Cell transmission failure cleared - APC to TADM
- 799Error codeThis event is generated if the bind procedure with the lower layer fails. The bind procedure can fail either due to the absence of bind confirm, or if there is a negative bind confirm from the lower layer. Not provisioned or software or CPU subsystem error
- 801Error codeIS-41 - Error adding Tag - sapId %d - dlgId %d - invokeId %d - oprCode %d
- 826Error codeThis event is generated if there are insufficient resources to initialize the Dialog Hash list. Software error
- 827Error codeThis event is generated if there are insufficient resources to initialize the Dialog Hash list. Corrupted disk file system or software or CPU subsystem error
- 828Error codeThis event is generated if there are insufficient memory resources to allocate for bitmap that is used for dialog pool mgmt. Software error
- 829Error codeThis event is generated if there are insufficient resources to initialize the Invoke Hash list. Corrupted disk file system or software or CPU subsystem error
- 831Error codeIndicates the IOM timed out during audio download. Faulted IOM
- 832Error codeIndicates a module failed during audio download. A component fault on the IOM or faulted IOM
- 834Error codeModule in slot %d has an IFE or EFE Fault
- 835Error codeIOM-%d unable to run scheduled exercise error-%d
- 839Error codeModule in slot %d is unprotected. Protection module is faulted or removed or provisioning error
- 840Error codeSP-%c unable to run scheduled exercise Error-%d
- 846Error codeSP-%c software version %s not on disk. Corrupted disk file system or Software or CPU subsystem error
- 847Error code%s ECC single bit error threshold crossed
- 855Error codeSAR on SF-%c Device error
- 856Error codeSAR on SF-%c PCI parity - abort fault
- 857Error codeSAR on SF-%c Parity error on Port to SAR bus
- 858Error codeSAR on SF-%c Synchronization error on Port to SAR bus
- 862Error codeOC alarm on the TDM IOM - alarm string looks like: IOM-%d-%s Loss of Signal. Possible cabling fault, provisioning error or faulted IOM
- 864Error codeOC alarm on the TDM IOM - alarm string looks like: IOM-%d-%s Loss of Frame. Possible cabling fault, provisioning error or faulted IOM
- 866Error code%s Alarm Indication Signal (line)
- 867Error code%s Alarm Indication Signal (line) cleared
- 868Error code%s Remote Defect Indication (line)
- 869Error code%s Remote Defect Indication (line) cleared
- 870Error code%s Device Error
- 881Error codeIOM-%d - Line Timing Out-of-Service. Incorrect provisioning or faulted IOM
- 884Error codeDefect cleared
- 897Error codeIOM-%d-ENET-%d Device Error %d