Kawasaki endüstriyel All models error codes
Codes
- E1158Error code(SSCNET)Servo error in JtXX
- E1159Error code(SSCNET)Error code for servo is (XX)
- E1160Error code(SSCNET)Servo error and monitor setting error of JtXX
- E1164Error code[LSEQ]Program execution error at control power ON.(CodeXX)
- E1169Error codeError in servo parameter change sequence.(CodeXX)
- E1171Error codeCC-LINK communication board is not installed
- E1172Error codeWeld communication board is not installed
- E1173Error codeServo communication error JtXX
- E1176Error code(SSCNET)Download error of external axis parameter
- E1179Error codeThe current under bending compensation is too large.(JtXX)
- E1180Error codeDownload error of external axis parameter.(JtXX)
- E1181Error codeEncoder battery low voltage.[Servo(XX)]
- E1182Error codeEncoder battery low voltage.[External axis(XX)]
- E1187Error codeCurrent command between Jt1 and Jt2 is interfered
- E1188Error code(SSCNET)Error in servo parameter change sequence.(CodeXX)
- E1189Error code(SSCNET)Regenerative error of JtXX.(CodeXX)
- E1190Error code(SSCNET)Speed error of JtXX.(CodeXX)
- E1191Error code(SSCNET)Motor overload of JtXX.(CodeXX)
- E1192Error code(SSCNET)Deviation error of JtXX.(CodeXX)
- E1193Error code(SSCNET)Encoder battery of JtXX is low voltage.(CodeXX)
- E1195Error code(Dual servo)Deviation error between master joint and slave joint
- E1198Error codeBrake check sequence error
- E1200Error code(Dual servo)Cannot compensate current error (deviation XX)
- E1204Error codeCurrent stretch over the limit
- E1208Error codeDownload error of servo parameter.(JtXX)
- E1209Error codeUpload error of servo parameter.(JtXX)
- E1215Error codeCurrent command causes interference between Jt4 and robot arm
- E1218Error codeCurrent command causes interference between Jt5 and Jt6
- E1237Error codeVision recognition error
- E1238Error codeVision communication error
- E1246Error codeCurrent command causes interference between Jt1, Jt2 and floor
- E1249Error codeTemperature in encoder is over the limit.(JtXX)
- E1251Error codeEEPROM access error occurred in encoder.(JtXX)
- E1252Error codeEncoder rotation data (internal) is abnormal.(JtXX)
- E1253Error codeUncoincidence error between request and response in encoder. (JtXX)
- E1255Error codeThe motor power of unchosen robot was turned on
- E1256Error codeInternal valve , sensor and error reset I/F board missing
- E1263Error codeEncoder temperature exceeded limit. (JtXX)
- E1264Error codeVelocity envelope error in endless rotation axis.(JtXX)
- E1267Error codeThe initial setting of Encoder is abnormal. (JtXX)
- E1268Error codeBreakage in the encoder line or faulty setting of encoder baud rate. (JtXX)
- E1283Error codeanalysis)The E1035 error occurs frequently.JtXX
- E1284Error codeanalysis)The E1035 and E1029 error occur at the same time.JtXX
- E1285Error codeanalysis)The E1035 and E1036 error occur at the same time.JtXX
- E1286Error codeanalysis)The E1035 and E1032 error occur at the same time.JtXX
- E1287Error codePower module error JtXX (UPPER)
- E1288Error codePower module error JtXX (LOWER)
- E1289Error code[Servo boardXX]Synchronous error.(Servo FPGA)
- E1290Error codeJtXX Voltage of the current sensor exceeded the upper limit
- E1291Error codeJtXX Current sensor is disconnected or out of order.(U)