JCB jeneratör All models error codes
Codes
- P06AError codeSensor supply monitoring error through DCU
- P20AError code
- P110AError codeFault which is set when no MDP updates occur on Injector 1 due to environmental conditions (as defined by the update strategy)
- P110BError codeFault which is set when no MDP updates occur on Injector 1 due to a fault within the update strategy
- P202AError code
- P202BError codeError for short to ground of DEF tank heater actuator powerstage
- P202CError codeError for short to battery of DEF tank heater actuator powerstage
- P202EError codeError on dosing valve plausibility
- P203BError codeTank level signal error
- P204BError codeError while monitoring the stabilisation of pressure
- P204CError codePump pressure signal below the minimum voltage limit
- P204DError codePump pressure signal above the maximum voltage limit
- P204FError codeError to detect the clogged filter
- P205BError codeError to indicate overheating of DEF tank
- P205CError codeDEF tank temperature signal voltage below minimum limit
- P205DError codeDEF tank temperature signal voltage above maximum limit
- P205EError codeDEF tank temperature signal error on CAN
- P207FError codeDEF quality error during refill condition
- P208AError code
- P208BError codeError on supply module pump speed permanent deviation
- P208CError codeShort circuit to ground error of supply module pump motor
- P208DError codeShort circuit to battery error of supply module pump motor
- P209FError codeError for overtemperature of DEF tank heater actuator powerstage
- P0659Error codeShort circuit to battery of actuator relay 1
- P0668Error codeECU internal temperature sensor low fault
- P0669Error codeECU internal temperature sensor high fault
- P0697Error codeECU Internal 5V Supply 2 auxillary fault
- P1101Error codeRail Pressure Control Error Positive fault
- P1102Error codeRail Pressure Control Error Negative fault
- P1103Error codeRail Pressure Fault detected - not able to maintain pressure after a stop and start request
- P1104Error codeFault which is set when no MDP updates occur on Injector 3 due to environmental conditions (as defined by the update strategy)
- P1105Error codeFault which is set when no MDP updates occur on Injector 3 due to a fault within the update strategy
- P1106Error codeFault which is set when no MDP updates occur on Injector 2 due to environmental conditions (as defined by the update strategy)
- P1107Error codeFault which is set when no MDP updates occur on Injector 2 due to a fault within the update strategy
- P1108Error codeFault which is set when no MDP updates occur on Injector 4 due to environmental conditions (as defined by the update strategy)
- P1109Error codeFault which is set when no MDP updates occur on Injector 4 due to a fault within the update strategy
- P1400Error codeErrorneous signal from override switch
- P1401Error codeCAN bus message error from override switch
- P1500Error codeFoot pedal signal fault set (triggers limp home mode)
- P1501Error codeFoot pedal signal fault set (triggers reduced torque mode)
- P1503Error codeHand pedal signal fault set (triggers limp home mode)
- P1504Error codeHand pedal signal fault set (triggers reduced torque mode)
- P1509Error codeCAN communication Error on TSC
- P1603Error codeFunctional Safety Fault
- P1604Error codeFunctional Safety Fault
- P1605Error codeFunctional Safety Fault
- P1606Error codeFunctional Safety Fault
- P2043Error codeCAN bus message error from head unit
- P2047Error codeDEF/AdBlue injector circuit open (SCR system fault)
- P2080Error codeTurbo in temperature count noise fault