Hyundai All models error codes
Codes
- CM1Error codeN100plus 004SF 015SF 004LF 037LF 004HF 037HF
- d01Error codeReal-time display of output frequency to motor, from 0.00 to 400.0 Hz, "Hz" LED ON
- d02Error codeReal-time display of output current to motor, from 0.0 to 99.9A, "A" LED ON
- d03Error codeReal-time display of output voltage to motor
- d12Error codeİnvertör DC bağlantı voltajını(V) gösterir
- d13Error code
- E05Error codeWhen the inverter output current causes the motor to overload, the electronic thermal trip in the inverter cuts off the inverter output
- E5Error codeDereboyu Caddesi No. 303 Kat. 2 Tel: (0212) 276 38 60
- E07Error codeIf regenerative energy from the motor or the main power supply voltage is high, the protective circuit activates to cut off the inverter output when the voltage of DC link exceeds the specification
- E08Error codeThe inverter output is cut off when EEPROM in the inverter has an error due to external noise, exc- essive temperature rise, or other factor
- E09Error codeWhen the input voltage receives by the inverter decreases, the control circuit does not function normally. When the input voltage is below the spe- cification, the inverter output is cut off
- E12Error codeWhen the external equipment or unit has an error, the inverter receives the corresponding signal and cuts off the output
- E13Error codeThe USP error is indicated when the power is turned on with the inverter in RUN state. (Enabled when the USP function selected)
- E14Error codeGround fault is detected between the inverter out- put section and the motor when the power is turned on, to protect the inverter
- E21Error codeWhen the temperature in the main circuit increases due to cooling fan stop, the inverter output is cut off.(only for the model type with cooling fan)
- E34Error codeThe inverter output was short-circuited. This con- dition causes excessive current for the inverter, so the inverter output is turned off
- E60Error codeThe inverter output is cut off when communication in the inverter has an error to external noise, excessive temperature rise, or other factor
- F01ParameterStandard default target frequency that determines constant motor that deter- mines constant motor speed. setting range is 0.00 to 400.0Hz (1) frequency setting from UP/DOWN key of digital operator. (2) Multi-step speed By combining frequency reference and intelligent input terminal ON/ OFF, up to 16 step of speed can be set. (3) Remote operator (NOP), control terminal input (O-L, OI-L). Frequency reference by the local potentiometer can be monitored
- F03ParameterStandard default deceleration, 2nd motor. minimum 0.1 999.9 ----- by 0.1sec setting range 1000 3000 ----- by 1sec
- H02Error codeTwo selections, option codes: 0.... Use standard motor data 1.... Use auto-tuning data
- I0Error codeU, V, W current (I ) (I ) (I ) U V W
- I1Error codeR S T Current (I ) (I ) (I ) R S T
- OnError codeBoard Diagnostics (OBD) Arıza Kodları Tespit Etme
- P0001Error codeP0099 OBD-II Arıza Kodları Anlamları ve Çözüm Yolları
- P0011Error codeVVT (Değişken Aroloji Zamanlaması) arızası - motorun performansını etkileyebilir
- P0014Error codeEksantrik Mili Zamanlama Hatası
- P0016Error codeKrank/eksantrik korrelyasiya A - Bank 1
- P0017Error codeKrank/eksantrik korrelyasiya B - Bank 1
- P0019Error codeKrank/eksantrik korrelyasiya B - Bank 2
- P0100Error codeMAF Sensörü Devre Arızası
- P0101Error codeMAF Sensörü Performans Arızası
- P0102Error codeHava axını sensörü (MAF) - siqnal çox aşağı
- P0103Error codeHava axını sensörü (MAF) - siqnal çox yüksək
- P0104Error codeHava axını sensörü (MAF) - aralıqlı xəta
- P0106Error codeMAP sensörü - siqnal aralığı xəta
- P0107Error codeMAP sensörü - siqnal çox aşağı
- P0108Error codeMAP sensörü - siqnal çox yüksək
- P0111Error codeQəbul hava temperaturu sensörü - siqnal aralığı xəta
- P0112Error codeQəbul hava temperaturu sensörü - siqnal çox aşağı
- P0113Error codeQəbul hava temperaturu sensörü - siqnal çox yüksək
- P0116Error codeSoyuducu temperatur sensörü - siqnal aralığı xəta
- P0117Error codeSoyuducu temperatur sensörü - siqnal çox aşağı
- P0118Error codeSoyuducu temperatur sensörü - siqnal çox yüksək
- P0121Error codeGaz kelebeği mövqe sensörü (TPS) - siqnal aralığı xəta
- P0122Error codeTPS - siqnal çox aşağı
- P0128Error code
- P0130Error codeLambda sensoru (Bank 1 Sensor 1) - dövrə xəta
- P0131Error codeOksijen sensörü düşük voltaj - oksijen sensörünün arızalandığını gösterir
- P0132Error codeLambda sensoru (Bank 1 Sensor 1) - siqnal çox yüksək
- P0133Error codeLambda sensoru (Bank 1 Sensor 1) - yavaş reaksiya