Hitachi MR cihazı All models error codes
Codes
- E01Error codeRF coil bağlantı hatası: Coil sisteminin düzgün takılmadığı ya da sinyal iletiminde kopukluk olduğu anlamına gelir
- E05Error codeSoğutma sistemi arızası: Cihazın ısınmasını engelleyen fan ya da soğutucu sistemde arıza olabilir
- E12Error codeYazılım senkronizasyon hatası: Donanım ve yazılım modülleri arasında uyumsuzluk mevcuttur
- EX92Error codeA parity error has occurred during reading by the CPU of the memory of the (main) J.NET or IR.LINK module
- EX93Error codeA parity error has occurred during reading by the CPU of the memory of the J.NET or IR.LINK (sub) module
- RS-232CError code
- S5CError code0 = Handler error not detected. 1 = Handler error detected
- S5DError code0 = Handler error not detected. 1 = Handler error detected
- S5EError code0 = Handler error not detected. 1 = Handler error detected
- S5FError code0 = Handler error not detected. 1 = Handler error detected
- S9AError code0 = Module operation stopped. 1 = Communication interrupted while the condition lasts; the register turns off when the problem is solved. 2 = Communication stopped. 3 = CAN transmission timed out. Communication interrupted while the condition lasts; the register turns off when the problem is solved. 4 = Station parameter setting error detected. Communication stopped. 5 = Station parameter set to a value indicating 17 or more frames to occur in each 10-ms interval. Communication stopped. F = The register does not turn off even when a serious problem arises
- S010Error codeS012 and S013 remain accessible only during one cycle (the RUN states include SIMU.RUN). S013 does not turn on upon a power failure
- S20FError code0 = Cell normal. 1 = Cell-related error
- S58BError code0 = Normal. 1 = RAM parity error
- S58CError code0 = Normal. 1 = RAM checksum error
- S58DError code0 = Normal. 1 = ROM checksum error
- S58EError code0 = Normal. 1 = WDT error (software)
- S58FError code0 = Normal. 1 = WDT error (hardware)
- S59BError code0 = Normal. 1 = RAM parity error
- S59CError code0 = Normal. 1 = RAM checksum error
- S59DError code0 = Normal. 1 = ROM checksum error
- S59EError code0 = Normal. 1 = WDT error (software)
- S59FError code0 = Normal. 1 = WDT error (hardware)
- S588Error codeLoaded with error information from µ RAM. • Cleared to 0 upon a power recovery or a reset. (µ: Microprogram) Normal values: 588=1 589=0 58A=0 58B=0 58C=0 58D=0 58E=0 58F=0
- S598Error codeLoaded with error information from µ RAM. • Cleared to 0 upon a power recovery or a reset. (µ: Microprogram) Normal values: 598=1 599=0 59A=0 59B=0 59C=0 59D=0 59E=0 59F=0
- S601Error code0 = Handler error not detected. 1 = Handler error detected
- S602Error code0 = TRCP error not detected. 1 = TRCP error detected
- S603Error code0 = RCS error not detected. 1 = RCS error detected
- S608Error codeError detail code
- S611Error code0 = Handler error not detected. 1 = Handler error detected
- S612Error code0 = TRCP error not detected. 1 = TRCP error detected
- S613Error code0 = System error not detected. 1 = System error detected
- S614Error codeReception handler error code
- S618Error codeError detail code
- S621Error code0 = Handler error not detected. 1 = Handler error detected
- S622Error code0 = TRCP error not detected. 1 = TRCP error detected
- S623Error code0 = RCS error not detected. 1 = RCS error detected
- S628Error codeError detail code
- S631Error code0 = Handler error not detected. 1 = Handler error detected
- S632Error code0 = TRCP error not detected. 1 = TRCP error detected
- S633Error code0 = System error not detected. 1 = System error detected
- S634Error codeReception handler error code
- S638Error codeError detail code
- S980Error code0 = Module operation stopped. 1 = Communication interrupted while the condition lasts; the register turns off when the problem is solved. 2 = Communication stopped. 3 = CAN transmission timed out. Communication interrupted while the condition lasts; the register turns off when the problem is solved. 4 = Station parameter setting error detected. Communication stopped. 5 = Station parameter set to a value indicating 17 or more frames to occur in each 10-ms interval. Communication stopped. F = The register does not turn off even when a serious problem arises
- S990Error code0 = Module operation stopped. 1 = Communication interrupted while the condition lasts; the register turns off when the problem is solved. 2 = Communication stopped. 3 = CAN transmission timed out. Communication interrupted while the condition lasts; the register turns off when the problem is solved. 4 = Station parameter setting error detected. Communication stopped. 5 = Station parameter set to a value indicating 17 or more frames to occur in each 10-ms interval. Communication stopped. F = The register does not turn off even when a serious problem arises
- SA00Error codeJ.NET main NET1
- SA01Error code0 = Operating normally. 1 = Hardware error detected
- SA08Error codeJ.NET main NET2
- SA09Error code0 = Operating normally. 1 = Hardware error detected
- SA80Error codeJ.NET sub-NET1