Hitachi hava perdesi All models error codes
Codes
- C1Error codeModel
- C096Error codeRS485 communication mode selection
- C100Error codeEzCOM start method selection
- C111Error codeOverload warning level 2
- C241Error codeOverload warning level, 2nd-motor
- C901Error codeOverload signal judgement cycle selection*3
- C902Error codeOverload signal filter time constant
- C903Error codeOverload signal hysteresis*3
- Cb-30Error code[Cb-32]
- Cb-31Error code[Cb-33]
- Cd-23Error code[Cd-33]
- Cd-24Error code[Cd-34]
- CE102Error codeInverter rated current×(0.00 to 2.00)(A)
- CE103Error codeInverter rated current×(0.00 to 2.00)(A)
- CE106Error codeInverter rated current×(0.00 to 2.00)(A)
- CE107Error codeInverter rated current×(0.00 to 2.00)(A)
- CF-05Error code00(Error)/ 01(Error output after Deceleration stop)/ 02(Ignore)/ 03(Free run stop)/ 04(Deceleration stop)
- CM2Error codeCommon terminal of [11] and [12] Allowable maximum current: 100 mA
- d030Error codePhase A/B pulse inputs from the encoder are not output correctly
- d081Error codeTrip monitor 1 to Trip monitor 6
- dA-60Error codeAAAAAAAA to VVVVVVVV [A:Current/V:Voltage] [Left](Ao4)(Ao3)(Ai5)(Ai4) (Ao2)(Ao1)(Ai2)(Ai1)[Right]
- dC-16Error codeLL to HH [L:Normal/H:Fatigued] [Left](FAN lifespan) [Right](board capacitor life span)
- dC-38Error code00(Other than below ) 01(OL notice ) 02(Motor thermal notice) 03(Controller thermal notice) 04(Motor overheating notice)
- dC-40Error code00(Other than below ) (Output terminal 007[IRDY]= ON, When the state is other than the following ) 01(Trip occurrence) 02(Power supply error) 03(Resetting) 04(STO) / 05(Standby) 06(Data Warning, etc) 07(EzSQ Sequence error) 08(Free run) / 09(Forced stop)
- dC-45Error codeMotor setup
- E07Error codeIncrease the deceleration time. Perform auto-tuning with a motor alone
- E051Error codeRefer to "15.2 Troubleshooting for Protection Functions Related Error" to resolve the cause
- E99Error codeAn error is detected in the internal circuit. The trip cannot be cancelled by inputting [RS] and STOP/RESET key. Trip can be canceled only by turning the power off and then on again
- E105Error codeThe speed deviation exceeded "[bb-83] Speed deviation error detection level"
- E106Error codePosition deviation exceeded "[bb-86] Position deviation error detection level"
- F002Error codeAcceleration time 1 setting or monitor, 1st-motor
- F003Error codeDeceleration time 1 setting or monitor, 1st-motor
- F202Error codeAcceleration time 1 setting or monitor, 2nd- motor
- F203Error codeDeceleration time 1 setting or monitor, 2nd- motor
- H001Error codeThe motor constants are measured without rotating the motor. Use this function when the motor must not rotate. Since the motor does not rotate, the motor constant I0 (no-load current) and motor constant J (moment of inertia) cannot be measured. Even if "Without rotation", the motor may rotate slightly
- H002Error codeAsync. Motor constant selection, 1st- motor
- H003Error codeAsync. Motor capacity
- H004Error codeAsync. Motor number of poles, 1st-motor
- H005Error codeAsync. Motor speed response, 1st-motor
- H006Error codeAsync. Motor stabilization constant, 1st- motor
- H020Error codeAsync. Motor constant R1, 1st- motor
- H021Error codeAsync. Motor constant R2, 1st- motor
- H022Error codeAsync. Motor constant L, 1st- motor
- H023Error codeAsync. Motor constant I0, 1st- motor
- H024Error codeAsync. Motor constant J, 1st- motor
- H030Error codeAsync. Motor constant R1, 1st- motor (Auto- tuning data)
- H031Error codeAsync. Motor constant R2, 1st- motor (Auto- tuning data)
- H032Error codeAsync. Motor constant L, 1st- motor (Auto- tuning data)
- H033Error codeAsync. Motor constant I0, 1st- motor (Auto- tuning data)
- H034Error codeAsync. Motor constant J, 1st- motor (Auto- tuning data)