Fanuc Alarm Listesi error codes
Codes
- 004Error codeADDRESS NOT FOUND
- 006Error codeILLEGAL USE OF NEGATIVE SIGN “
- 007Error codeILLEGAL USE OF DECIMAL POINT
- 010Error codeIMPROPER G---CODE Kullanılamaz bir G kodu veya sağlanmayan fonksiyona karşılık gelen
- 020Error codeOVER TOLERANCE OF RADIUS
- 031Error codeILLEGAL P COMMAND IN G10
- 032Error codeILLEGAL OFFSET VALUE IN G10
- 035Error codeCAN NOT COMMANDED G31
- 037Error codeCAN NOT CHANGE PLANE IN NRC
- 038Error codeINTERFERENCE IN CIRCULAR BLOCK
- 039Error codeCHF/CNR NOT ALLOWED IN NRC
- 040Error codeINTERFERENCE IN G90/G94 BLOCK
- 041Error codeINTERFERENCE IN NRC
- 048Error codeBASIC 3 AXIS NOT FOUND Üç boyutlu takım kompanzasyonunun ya da üç boyutlu
- 050Error codeCHF/CNR NOT ALLOWED IN THRD BLK
- 052Error codeCODE IS NOT G01 AFTER CHF/CNR
- 055Error codeMISSING MOVE VALUE IN CHF/CNR
- 056Error codeNO END POINT & ANGLE IN CHF/CNR
- 057Error codeNO SOLUTION OF BLOCK END
- 058Error codeEND POINT NOT FOUND
- 059Error codePROGRAM NUMBER NOT FOUND
- 060Error codeSEQUENCE NUMBER NOT FOUND Komut sıra numarası sıra numarası aramasında
- 061Error codeADDRESS P/Q NOT FOUND IN G70---G73
- 063Error codeSEQUENCE NUMBER NOT FOUND
- 064Error codeSHAPE PROGRAM NOT MONOTONOUSLY
- 065Error codeILLEGAL COMMAND IN G71---G73
- 066Error codeIMPROPER G---CODE IN G71---G73 G71,
- 067Error codeCAN NOT OPERATE IN MDI MODE P ve Q adresiyle G70, G71, G72 veya G73 komutu
- 069Error codeFORMAT ERROR IN G70---G73 G70, G71, G72 veya G73’ün P ve Q’suyla belirtilen
- 070Error codeNO PROGRAM SPACE IN MEMORY Bellek alanı yetersiz.
- 071Error codeDATA NOT FOUND Aranacak adres bulunamadı. Veya belirtilenprogramnumaralı program,
- 073Error codePROGRAM NUMBER ALREADY IN USE
- 074Error codeILLEGAL PROGRAM NUMBER Program numarası 1 --- 9999 arasında değil.
- 075Error codePROTECT Numarası korunan bir programı kaydetmek için girişimde bulunuldu.
- 076Error codeADDRESS P NOT DEFINED M98,G65 veyaG66Dkomutu içeren blokta Padresi (program
- 080Error codeG37 ARRIVAL SIGNAL NOT ASSERTED
- 081Error codeOFFSET NUMBER NOT FOUND IN G37
- 082Error codeT---CODE NOT ALLOWED IN G37 T kodu ve otomatik takım kompanzasyonu (G36, G37)
- 083Error codeILLEGAL AXIS COMMAND IN G37 Otomatik takım kompanzasyonunda (G36, G37),
- 085Error codeCOMMUNICATION ERROR
- 088Error codeG LAN FILE TRANS ERROR (CHANNEL-1)
- 089Error codeG LAN FILE TRANS ERROR (CHANNEL-2)
- 092Error codeAXES NOT ON THE REFERENCE POINT
- 094Error codeP TYPE NOT ALLOWED (COORD CHG)
- 095Error codeP TYPE NOT ALLOWED (EXT OFS CHG)
- 096Error codeP TYPE NOT ALLOWED (WRK OFS CHG)
- 097Error codeP TYPE NOT ALLOWED (AUTO EXEC)
- 098Error codeG28 FOUND IN SEQUENCE RETURN
- 099Error codeMDI EXEC NOT ALLOWED AFT. SEARCH
- 109Error codeFORMAT ERROR IN G08