Cisco All models error codes
Codes
- 13Error codeWhen a Cisco router encounters error code 13, the message call path from an unidentified routing client %1, dn= %2 is displayed and action will be taken as in the form of checking the dialed number and routing client settings and then correct the problem
- 62Error codeWhen a Cisco router encounters error code 62, the message-router receives a call route request from routing client%2 with an unconfigured called number%3. will be displayed and action will be taken as- update the Central Controller and configure the dialed number for the Routing Client
- 63Error codeWhen a Cisco router encounters error code 63, the message-router could not find a call type that specified the called number as %2. the caller digit is "%3" and ANI is "%4" is displayed and action will be taken as- use the script editor to update the Central Controller and dialed numbers with the appropriate call type
- 64Error codeWhen a Cisco router encounters error code 64, the message-Scheduled script not found for incoming number %3 (ID %1) with call type %4 (ID %2) is displayed. In other words, there are currently no scripts scheduled to run for call type %4 and dialed number %3 and action will be taken to use the Script Editor to schedule a script to run for this dialed number and call type and update the Central Controller
- 65Error codeWhen a Cisco router encounters error code 65, the message- Script%3 (ID%1) failed to generate a route for the phoned number%4 with call type%5 (ID%2) is displayed. In other words, the use of script%3 was triggered by a call with called number%4 and call type%4, however there was no route set for this phoned number and call type and action will be taken as- the script configuration produced no output. This is generally a failure path in the script that was not corrected. Examine and update the script for the supplied call number and call type
- 66Error codeWhen a Cisco router encounters error code 66, the message-there is no default label for phoned number%2 (ID%1) is displayed. In other words, there is no default label set for dialed number%2, but the Router requires one and the action will be taken as- Because of a previous issue, the default label is the last resort for routing calls. Using default labels for CCE is NOT advised. Examine event messages with Event Viewer for error situations related to resources for the phoned number
- 67Error codeWhen a Cisco router encounters an error code 67, the message-There is no availability of label for announcement%3 (ID%1) from phoned number%4 (ID%2) is displayed. In other words, there is no label for announcement%3 from dialed number%4 and action will be taken as to create a suitable label for the announcement and update the Central Controller
- 68Error codeWhen a Cisco router encounters error code 68, the message-there is no peripheral target for route%3 (ID%1) with routing client%4 (ID%2) is displayed. In other words, there are no available peripheral targets for route%3 for routing client%4 and action will be taken as setting up a suitable peripheral target for the route and updating the Central Controller
- 123Error codeWhen a Cisco router encounters error code 123, the message-there are no routes set for the translation route%2 (ID%1) is displayed. In other words, there were no routes specified for translation route%2, and action will be taken as- associate the right set of routes to correct the translation route setup
- 230Error codeWhen a Cisco router encounters error code 123, the message- there was no busy label for routing client%3 (ID%), phoned number%4 (ID%) is displayed. In other words, a script specified that for phoned number%4, a busy label should be returned to the routing client%3, however, no such label is configured and action will be taken to set a busy label for the Routing Client you've chosen
- ais10Error code(Major)
- and622Error codeIndication (Severity)
- ast24Error codeFraming Bit Error (BE)
- b1Error code# section BIP-8 errors
- b2Error code# line BIP-8 errors
- b3Error code# path BIP-8 errors
- CE100TError codeFAN: EQPT-MISS (CR)
- DS1Error codeMFGMEM (FAN)
- DS3Error codeAny alarms detected by the controller are displayed here. The possible alarms are
- E1Error codeIndication (Severity)
- E3Error codeIndication (Severity)
- erf11Error codeRAI indicates a problem between the ATM switch router interface transmitter and the far end receiver, but it may not be in the segment between the ATM switch router and the adjacent node
- g1Error code# path FEBE errors
- I5Error codeOutput port A:15 is detected instead of the expected input port A:15. This test result message alternates on the lower half of the screen. This “error” could occur if the user has not yet moved the test cord from the output port just tested to the next port in sequence, the input port. The printed report for this error would appear as A: 15 WE=>OUT A: 15
- LOP11Error codeIndicates that the far-end equipment is malfunctioning
- mr0xError codeIndication (Severity)
- OC-3cError codeErrors could be: SECTION LOS SECTION LOF LINE AIS LINE RDI PATH LOP (Path Loss of Pointer) PATH AIS PATH RDI Invalid OOCD (out of cell delineation)
- OC-12cError codeIndication (Severity)
- OC-48cError codeOff Flashing green Red
- ode448Error codeWhen a Cisco router encounters error code 448, the message “Dialog (%1) aborted and was erased” is displayed. Issue 448, which happens when the customer leg of the call is severed in the routing client, is not a routing error. Select ICM Admin Workstation > Schema Help > Contents > ICM Master Help Option > Help Option from the program's menu.Click on ICM error after selecting the name of your router. Await for the error popup box to appear. Read the entire error message.Apply patches via SR2 or Hotfix 162 for ICM 4.6.2 to modify how error code 448 is applied when calls are abandoned. To confirm that the issue has been resolved, check your router
- T1Error codeErrors could be: SECTION LOS SECTION LOF LINE AIS LINE RDI PATH LOP (Path Loss of Pointer) PATH AIS PATH RDI Invalid OOCD (out of cell delineation)
- z2Error code# line FEBE errors