Bmw All models error codes
Codes
- OnError codeBoard Diagnostics (OBD) Arıza Kodları Tespit Etme
- P0011Error codeIncorrect position of the camshaft, the problem is in the first bank of the engine. The engine control unit reports a too early opening angle of the valves, a malfunction of the system is noted. The cause of problem P0011 may be in the operation of the engine control unit
- P0012Error codeDelay of position A of the camshaft in the first bank. With such an error, the Check indicator is always on on the dashboard Engine . Reasons that could lead to this problem: low level of engine fluid or lubricant is critically dirty, it is necessary to change consumables; malfunctions or malfunction of the mechanism for changing the valve timing; malfunctions in the operation of the engine fluid control valve; malfunction of the wiring supplying the lubrication control valve, a short circuit is possible; problems associated with the functioning of the ECM control module
- P12BError codeFuel injection time error in the fourth cylinder of the engine - fuel is supplied too early. If the problem appeared after washing the engine, it is necessary to dry all the contacts on the high-voltage cables
- P13BError codeMalfunction of the vanos valve or device mesh. The problem is accompanied by a decrease in the power of the power unit
- P13CError codeThe variable valve timing system is defective.
- P0014Error codeMalfunctions in the drive mechanism for changing the valve timing. Too early valve opening angle reported
- P14AError codeParticulate filter malfunction.
- P0015Error codeMalfunctions in the operation of the drive device of the variable valve timing system. The problem is related to the release in the first bank of the engine.
- P0022Error codeIncorrect position of the camshafts. The problem is that the valve opening angle is too late. The cause of the malfunction may be the incorrect alignment of the marks on the pulleys or malfunctions in the operation of the control module
- P0036Error codeMalfunction in the heating device of the oxygen sensor 2, installed in the first bank of the engine.
- P0056Error codeMalfunction in the operation of the heated oxygen controller No. 2 installed in the second bank of the engine. The problem lies in the operation of the control line of the heating device or the sensor itself.
- P110DError codeThrottle position controller malfunction. The data coming from the controller is out of range.
- P111BError codeAir flow meter malfunction. Problems with this sensor will result in air-fuel mixture formation errors. This will cause incorrect operation of the engine, up to a decrease in power and its arbitrary stop
- P114BError codeMalfunctions in the fuel balance formation system. The data received by the microprocessor does not correspond to the normalized parameters or is out of range of acceptable values.
- P115CError codeMalfunctions in the mass air flow sensor. The control unit notes that an incorrect signal is being sent from the device to the microprocessor, or the sensor cannot pass a sufficient amount of air flow through itself into the engine cylinders
- P0128Error codeTermostat / Motor Geç Isınıyor
- P0135Error codeMalfunction in the operation of the heated oxygen controller 1 installed in the first bank of the engine. The cause of the problem is a malfunction in the control of the heating system, which may be due to damage or faulty wiring
- P0170Error codeMalfunctions in the fuel balance system. A malfunction is usually accompanied by a limitation in engine power
- P0173Error codeMalfunctions in the fuel balance system. The problem is in the second bank of the power unit. The reason may be a malfunction of the fuel pump or one of the elements of the ignition system.
- P0201Error codeEnjektör Devresi Arızası
- P0235Error codeCode 0235 appears when there is a malfunction in the boost controller A of the turbocharger unit. The problem may be due to a malfunction in the drive supercharger or damage to the power line connected to it
- P0313Error codeThe powertrain control unit detected a misfire caused by a low fuel level in the tank.
- P0335Error codeMalfunctions in the functioning of the crankshaft position controller . The problem is the lack of a signal, which may be due to the failure of the regulator or damage to the power and control cable
- P0340Error codeMalfunction of the camshaft position sensor. The cause of the problem may be due to the absence of a signal, which is associated with damaged wiring.
- P0365Error codeBreakdown or absence of a signal coming from the controller In the position of the camshaft . Problems in the operation of the first bank of the engine. The cause of the malfunction may be related to wiring or poor contact
- P0366Error codeMalfunction in the operation of the controller In the position of the camshaft, the control unit recorded problems in the operation of the first bank of the engine. The signal coming from the controller is out of the allowed operating range
- P0401Error codeMalfunction associated with the functioning of the exhaust gas recirculation system. The problem lies in the insufficient level of recirculation
- P0412Error codeDamage or breakage of the power line connected to the solenoid valve A for the supply of air flow to the outlet
- P0430Error codeMalfunctions of the catalytic converter. The control unit has fixed a problem in the operation of the second bank of the engine - the performance is below the critically acceptable threshold
- P0444Error codeEvaporative accumulator solenoid valve failure due to broken wiring or lack of contact.
- P0491Error codeMalfunctions in the exhaust air supply system, the problem lies in the first bank of the engine
- P0505Error codeThis code appears when there is a malfunction in the idle speed control system. The problem may be a sensor malfunction or poor device contact
- P0597Error codeWith this error, the engine control unit reports problems associated with the operation of the thermostat heating element control mechanism.
- P0600Error codeFaulty CAN data bus
- P0720Error codeMalfunctions in the output shaft speed controller. The control unit notes that the problem may be a power line failure caused by a damaged or broken cable. Also, the problem may be in the controller itself or a short circuit in the control wire
- P0733Error codeIncorrect gear ratio in the third gear of the box.
- P0748Error codeFailure of the solenoid valve for controlling the pressure of the working fluid of the gearbox. The problem is electrical, in this case, the connection and contacts are diagnosed
- P1050Error codeMalfunction in the operation of the Valvetronic system - raising the intake valves. The problem is accompanied by the appearance of the Check indicator on the dashboard, as well as the transition of the power unit to half power mode. The reason may be a malfunction of the system control module or damage to the power line
- P1057Error codeMalfunctions in the operation of the electric motor of the drive device for changing the valve timing. The problem is damage or breakage of the power supply voltage
- P1062Error codeMalfunction in the operation of the variable valve timing system. The engine control unit can put the power unit into emergency operation mode. It is noted that the shafts do not reach the extreme position
- P1083Error codeLean air-fuel mixture registered by the engine control unit in one of the engine cylinders. The error indicates a malfunction in the functioning of the first oxygen sensor, but the problem may be related to the control unit
- P1180Error codeThe code translates to “Heated Oxygen Sensor 2 Bank 1 Slow Response”
- P1189Error codeMalfunctions in the operation of the mixture composition regulator marked 1, installed in the second bank of the engine. The readings from the device are out of range
- P1250Error codeA critically high level of air pressure recorded in the intake manifold. If these elements are intact, the ECM is subject to diagnosis
- P1343Error codeCombinations P1343 or 1343 report a misfire with a fuel cut-off, recorded in the operation of the first cylinder of the engine. If one of the sensors is faulty, then with such a problem, the Check icons or an exclamation mark in a circle are lit on the dashboard
- P1353Error codeThis code on the BMW E38, 4X4 and other versions indicates the shutdown of the sixth cylinder of the power unit and the interruption of the fuel supply. The problem lies in the misfire of the air-fuel mixture with fuel cut-off. The reasons that could lead to the appearance of this malfunction: damage or broken wiring; low fuel level in the tank; malfunction of the fuel system; lack of tightness in the intake system; mechanical problems in the engine
- P1553Error codeIncorrect reference value in the position of the crankshaft and camshaft intake valves. The value obtained is out of range
- P1619Error codeA critically low signal has been registered on the cooling system thermostat control line. Perhaps the thermostat is stuck in one of the positions and this problem is not permanent, but periodic
- P1622Error codeThis control code reports an electrical failure or a break in the thermostat power supply wiring. There may be malfunctions in the cooling system, up to engine overheating