Yaskawa All models error codes
Codes
- 0Error codeCheck the alarm history display (Fn000) to see if the overload alarm was reported
- 0bError codeCancelled Servo ON Command Alarm
- 7AError codeHeat Sink Overheated(Detected when the heat sink temperature exceeds 100°C.)
- 8AError codeExternal Encoder Error
- 020Error codeThe power supply voltage suddenly dropped
- 021Error codeThe software version of SERVOPACK that caused the alarm is older than that of the written parameter
- 022Error codeThe power supply voltage suddenly dropped
- 030Error codeA SERVOPACK fault occurred
- 30-200Error codeMOTOR CURRENT PCaornasmteatnetr n n50774 Ssettingg t OUTPUT FREQ. t
- 050Error codeCombination Error (The SERVOPACK and servomotor capacities do not correspond.)
- 051Error codeUnsupported Device Alarm
- 100Error codeOvercurrent or Heat Sink Overheated(An overcurrent flowed through the IGBT or heat sink of SERVOPACK overheated.)
- 122Error codeFault Display
- 300Error codeRegeneration Error
- 320Error codeRegenerative Overload
- 330Error codeMain Circuit Power Supply Wiring Error (Detected when the power to the main circuit is turned ON.)
- 400Error codeOvervoltage (Detected in the SERVOPACK main circuit power supply section.)
- 410Error codeUndervoltage (Detected in the SERVOPACK main circuit power supply section.)
- 450Error codeMain-Circuit Capacitor Overvoltage
- 520Error codeVibration Alarm
- 521Error codeAutotuning Alarm (Vibration was detected while executing the advanced autotuning, one-parameter tuning, EasyFFT, or tuning-less function.)
- 710Error codeIncorrect wiring or contact fault of servomotor and encoder
- 730AError codeDynamic Brake Overload (An excessive power consumption of dynamic brake was detected.)
- 740Error codeOverload of Surge Current Limit Resistor(The main circuit power is turned ON/OFF too frequently.)
- 810Error codeEncoder Backup Error(Only when an absolute encoder is connected.)(Detected on the encoder side.)
- 820Error codeEncoder Checksum Error(Detected on the encoder side.)
- 830Error codeAbsolute Encoder Battery Error(The absolute encoder battery voltage is lower than the specified value.)
- 840Error codeEncoder Data Error(Detected on the encoder side.)
- 850Error codeEncoder Overspeed(Detected when the control power supply was turned ON.)(Detected on the encoderside.)
- 860Error codeEncoder Overheated(Only when an absolute encoder is connected.)(Detected on the encoder side.)
- 1000Error codeAşırı akım - servo amplifikatörü koruması
- 1030Error codeDC bus aşırı voltaj
- 1105Error codeMotor aşırı ısınma
- 4117Error codeEncoder iletişim hatası
- 4328Error codeFren kontrol hatası
- A0001Error codeHeavy Duty Max. Motor Capacity Rated Output No. kW Current A 0001 0.1 0.8 0002 0.2 1.6 0003 0.4 3.0 0006 0.75 5.0 0010 1.5 8.0 0012 2.2 11.0 0018 3.7 17.5
- A1Error code02 (Motor 1 Control Mode) Dependent Parameters. . . . . . 368
- A1-01Error codeThe drive is not in the Drive Mode. The button was pushed. Auto-Tuning has just completed. A Fast-Stop was executed and has not yet been reset. Settings are incorrect for the source that provides the run command. One of the Safety Inputs is open. There is faulty wiring in the control circuit termina
- A1-02ParameterFrequency reference is too low. Load is too heavy. The torque limit function is operating in Open Loop Vector Control. Acceleration time has been set too long. Motor characteristics and drive parameter settings are incompatible with one another in V/f Control. The right combination of motor characte
- A1-03Error codeSelects a method to initialize the parameters. 0: No Initialize 1110: User Initialize (The user must first program and store desired settings using parameter o2-03) 2220: 2-Wire Initialization (parameter initialized prior to shipment) 3330: 3-Wire Initialization 5550: oPE4 Fault reset
- A1-04Error codeThe drive is not in the Drive Mode. The HAND button was pressed. Auto-Tuning has just completed. A Fast Stop was executed and has not yet been reset. Settings are incorrect for the source that provides the Run command. There is faulty wiring in the control circuit terminals. The drive has been set t
- A2-1Error codeInstantaneous overcurrent
- age40Error codeeck for proper grounding of drive and motor
- age400Error codeck for proper grounding of drive and motor
- at5Error codeDrive is attempting to operate the motor at 5% or less of the speed reference value
- b1-02Error codeRun Command Selection
- b1-03Error codeDC Injection Braking at Stop cannot be selected when using Open Loop Vector for PM motors
- b1-04Error codeReverse Operation Selection
- b10Error codeSpeed Reference A/D Error(Detected when the servo is ON.)
- b11Error codeSpeed Reference A/D Data Error