Yaskawa SGD7C error codes
Codes
- CA372Error codeLogging File Writing Error
- CA401Error codeM-III Restriction Condition Error
- Cb0Error codeThe contents of communications with the encoder are incorrect
- CE051Error codeModule Synchronization Error
- CE071Error codeUnsupported Module Detected Error
- CE081Error codeCPU Fatal Internal Temperature Error 1
- CE082Error codeCPU Fatal Internal Temperature Error 2
- CE090Error codeHardware Error 1
- CE091Error codeHardware Error 2
- CE092Error codeHardware Error 3
- CF1Error codeReception Failed Error in Feedback Option Module Communications
- CF2Error codeTimer Stopped Error in Feedback Option Module Communications
- d00Error codeThe setting of Pn520 (Position Deviation Over- flow Alarm Level) was exceeded by the posi- tion deviation while the servo was ON
- d01Error codeThe servo was turned ON after the position deviation exceeded the setting of Pn526 (Position Deviation Overflow Alarm Level at Servo ON) while the servo was OFF
- d02Error codeIf position deviation remains in the error counter, the setting of Pn529 or Pn584 (Speed Limit Level at Servo ON) limits the speed when the servo is turned ON. This alarm occurs if a position reference is input and the setting of Pn520 (Position Deviation Overflow Alarm Level) is exceeded before the limit is cleared
- E00Error codeAn initialization timeout error occurred in the Controller Section
- E02Error codeA synchronization error occurred between the Controller Section and SERVOPACK
- E03Error codeA synchronization error occurred in the Con- troller Section
- E50Error codeA synchronization error occurred in the Con- troller Section
- E51Error codeA failure occurred in the SERVOPACK
- E61Error codeAn error occurred in the transmission cycle of the Controller Section
- E72Error codeFeedback Option Module Detection Failure
- EA2Error codeA synchronization error occurred between the Controller Section and Servo Section
- EB0Error codeSafety Function Drive Monitor Circuit Error*2
- EB1Error codeSafety Function Signal Input Timing Error
- EB2Error codeSafety Function Drive Internal Signal Error*2
- EB3Error codeSafety Function Drive Communications Error 1*2
- EB4Error codeSafety Function Drive Communications Error 2*2
- EB5Error codeSafety Function Drive Communications Error 3*2
- EB6Error codeSafety Function Drive Communications Data Error*2
- EC7Error codeSafety Option Card Stop Command Error*2
- Ed1Error codeA timeout occurred for a communications command in the Controller Section
- F10Error codeThe voltage was low for more than one sec- ond for phase R, S, or T when the main power supply was ON
- F50Error codeA failure occurred in the SERVOPACK
- FL-1Error codeA failure occurred in the SERVOPACK
- IL02Error codeWarnings (IL 02)
- is4Error codeWatchdog error for MEMOBUS response
- RAM00Error codeGives the error that has occurred when the message function was executed. This information is useful for troubleshooting errors that can occur when mes- sage function parameters are not properly set
- RAM01Error codeThis information is useful when a Transmission Section Error (88 hex), which cannot be isolated with the processing results in PARAM00, has occurred
- RAM02Error codeSupplemental information for PARAM00 (Processing Result). These parameters give the error code from the remote device
- SW0005Error codeSystem Error Status
- SW0008Error codeUser Operation Error Status
- SW0009Error codeSystem Service Execution Status
- SW0011Error codeDetailed User Operation Error Status
- SW0020Error codeSystem I/O Error Status
- SW0956Error codeExtended System I/O Error Status
- SW1620Error codeAlarm History Information
- SW2500Error codeAutomatic Reception Status for Ethernet Communications
- to32Error codeode
- x040Error codeReal number operation error in standard Operation is aborted and output is set to system function 0.0. x040 hex: SQRT x047 hex: EXP x04E hex: PD x055 hex: SLAU x041 hex: SIN x048 hex: LN x04F hex: PID x056 hex: REM x042 hex: COS x049 hex: LOG x050 hex: LAG x057 hex: RCHK x043 hex: TAN x04A hex: DZA x051 hex: LLAG x058 hex: BSRCH x044 hex: ASIN x04B hex: DZB x052 hex: FGN x059 hex: SORT x045 hex: ACOS x04C hex: LIM x053 hex: IFGN - x046 hex: ATAN x04D hex: PI x054 hex: LAU