Slant/Fin All models error codes
Codes
- 29Error codeInternal fault: Flame bias cannot be set in range
- 30Error codeExcess Flue Temperature
- 31Error codeInternal fault: SLO electronics unknown error
- 32Error codeExcess Water Inlet Temperature
- 33Error codeFan Failure - RPM Error
- 285Error codeAbnormal Recycle: Demand off during Pre-Ignition test
- 286Error codeAbnormal Recycle: Demand off during Pre-Ignition time
- 287Error codeAbnormal Recycle: Flame was on during Safe Start check
- 288Error codeAbnormal Recycle: Flame was on during Drive to Purge Rate
- 289Error codeAbnormal Recycle: Flame was on during Measured Purge Time
- 290Error codeAbnormal Recycle: Flame was on during Drive to Light off Rate
- 291Error codeAbnormal Recycle: Flame was not on at end of Ignition period
- 292Error codeAbnormal Recycle: Flame was lost during Main Flame Establishing Period
- 293Error codeAbnormal Recycle: Flame was lost early in Run
- 294Error codeAbnormal Recycle: Flame was lost during Run
- 296Error codeAbnormal Recycle: Interrupted air flow switch was off during Drive to Purge Rate
- 297Error codeAbnormal Recycle: Interrupted air flow switch was off during Measured Purge Time
- 298Error codeAbnormal Recycle: Interrupted air flow switch was off during Drive to Light off Rate
- 299Error codeAbnormal Recycle: Interrupted air flow switch was off during Pre-Ignition test
- 300Error codeAbnormal Recycle: Interrupted air flow switch was off during Pre-Ignition time
- 301Error codeAbnormal Recycle: Interrupted air flow switch was off during Main Flame Establishing Period
- 302Error codeAbnormal Recycle: Ignition failed due to interrupted air flow switch was off
- 306Error codeAbnormal Recycle: ILK off during Pre-Ignition test
- 307Error codeAbnormal Recycle: ILK off during Pre-Ignition time
- 308Error codeAbnormal Recycle: ILK off during Main Flame Establishing Period
- 309Error codeAbnormal Recycle: ILK off during Ignition period
- 313Error codeRun was terminated due to fan failure
- 314Error codeAbnormal Recycle: Fan failed during Drive to Purge Rate
- 315Error codeAbnormal Recycle: Fan failed during Measured Purge Time
- 316Error codeAbnormal Recycle: Fan failed during Drive to Light off Rate
- 317Error codeAbnormal Recycle: Fan failed during Pre-Ignition test
- 318Error codeAbnormal Recycle: Fan failed during Pre-Ignition time
- 319Error codeAbnormal Recycle: Fan failed during Ignition period
- 320Error codeAbnormal Recycle: Fan failed during Main Flame Establishing Period
- 324Error codeAbnormal Recycle: Hardware flame bias
- 325Error codeAbnormal Recycle: Hardware static flame
- 326Error codeAbnormal Recycle: Hardware flame current invalid
- 327Error codeAbnormal Recycle: Hardware flame rod short
- 330Error codeAbnormal Recycle: Hardware SLO flame ripple
- 331Error codeAbnormal Recycle: Hardware SLO flame sample
- 332Error codeAbnormal Recycle: Hardware SLO flame bias range
- 333Error codeAbnormal Recycle: Hardware SLO flame bias heat
- 336Error codeAbnormal Recycle: Hardware SLO static flame
- 352Error codeAbnormal Recycle: fault stack sensor
- 355Error codeAbnormal Recycle: fault outlet sensor
- 357Error codeAbnormal Recycle: fault DHW sensor
- 359Error codeAbnormal Recycle: fault inlet sensor
- 374Error codeAbnormal Recycle: Hardware flame bias high
- 375Error codeAbnormal Recycle: Hardware flame bias low
- 376Error codeAbnormal Recycle: Hardware flame bias delta high