Schwörer klima santrali All models error codes
Codes
- E01Error codeserial comms error, mis-setting, RC is detecting error signal from IU, outdoor system address, indoor system address, or IU individual/main/sub setting it not set, auto address is not complete
- E02Error codeserial comms error, mis-setting, RC is detecting error signal from IU, error in transmitting serial comm signal
- E2Error codeİç Ünite Donma Koruması
- E03Error codeIU is detecting error signal from remote controller (and system controller)
- E04Error codeIU is detecting error signalled from OU, error in receiving serial comms signal
- E4Error codeYüksek veya Düşük Basınç Arızası
- E05Error codeIU is detecting error signalled from OU, error in transmitting serial comms signal
- E5Error codeİç ve Dış İletişim Ünitesi Hatası
- E06Error codeOU is detecting error signalled from IU, error in receiving serial comms signal (inc unit qty verification failure)
- E07Error codeOU is detecting error signalled from IU, error in transmitting serial comms signal
- E7Error codeKompresör Koruma Arızası
- E8Error codeDış Ünite Aşırı Isınma Koruması
- E10Error codeIU is detecting error signalled from signal option, error in transmitting serial comms signal
- E11Error codeIU is detecting error signalled from signal option, error in receiving comms signal
- E12Error codeIU is detecting error signalled from signal option, because auto address setting is in process in a different system, auto address is setting start is prohibited
- E14Error codesetting error, main unit duplication in simultaneous-operation multi control (detected by outdoor unit)
- E17Error codean IU detected trouble in the signal from another IU, error in transmitting serial comms signal
- E18Error codean IU detected trouble in the signal from another IU, error in receiving serial comms signal
- E24Error codeAuto address error, Main OU is detecting error signal from sub OU
- E25Error codeAuto address error, of OU address setting
- E26Error codeAuto address error, the number of connected main and sub OU do not correspond to the number set at the main OU PCB
- E29Error codeauto address error, sub OU in receiving serial comm signal from main OU
- F0Error codeSoğutucu Gaz Kaçağı
- F01Error codethermistor fault, indoor coil temp. sensor (E1)
- F02Error codethermistor fault, indoor coil temp. sensor (E2)
- F03Error codethermistor fault, indoor coil temp. sensor (E3)
- F04Error codeOutdoor thermistor open circuit, discharge TD1
- F05Error codeOutdoor thermistor open circuit, discharge TD2
- F06Error codeOutdoor thermistor open circuit, heat exchanger temperature C1
- F07Error codeOutdoor thermistor open circuit, heat exchanger temperature C2
- F08Error codethermistor fault, outdoor air temp. sensor (air temp)
- F10Error codethermistor fault, indoor suction air (room) temp sensor (TA)
- F11Error codethermistor fault, indoor discharge air temp. sensor (BL)
- F12Error codeOutdoor thermistor open circuit, intake temperature TS
- F16Error codethermistor fault, outdoor high pressure sensor
- F17Error codethermistor fault, outdoor unit low pressure sensor
- F22Error codethermistor fault, outdoor unit compressor 3 (constant speed) discharge temp sensor
- F23Error codethermistor fault, outdoor No. 2 coil gas temp (EXG2)
- F24Error codethermistor fault, outdoor No. 2 coil liquid temp. sensor (EXL2)
- F25Error codethermistor fault, outdoor unit heat exchanger 3 gas temp. sensor
- F26Error codethermistor fault, outdoor unit heat exchanger 3 liquid temp. sensor
- F29Error codeindoor EEPROM error
- F31Error codeoutdoor EEPROM error
- H01Error codeAC1 compressor protection, overload current was detected
- han14Error codeFaulty rectifi er-regulator; replace
- han28Error codeStator is faulty; replace. Test stator further using an ohmmeter (steps 3 and 4)
- is28Error codeStator is OK. Rectifi er- regulator is faulty; replace
- L18Error code4-way valve operation failure
- P17Error codeincorrect discharge temperature (comp no 2)