Pacsystems All models error codes
Codes
- 0-3Error codeCommand Response
- 1-3ParameterCurrent mode input jumper for Channel 1
- 1-4Error codeOutput has overcurrent fault
- 1-16Error codeAmber: Input fault
- 2-4ParameterCurrent mode input jumper for Channel 2
- 4-7Error codeAddress
- 11-13ParameterCurrent mode input jumper for Channel 3
- 12-14ParameterCurrent mode input jumper for Channel 4
- acy45Error code0.1% of range at 25°C 0.2% of range over entire temperature span
- acy48Error code±10 mV/40 µA (typical) over operating temperature ±30 mV/160 µA (maximum) over operating temperature
- acy50Error code±0.25% of full scale at 25°C (77°F) ±0.5% of full scale over specified operating temperature range
- acy53Error code±0.25% of full scale at 25°C (77°F): ± 0.5% of full scale over specified operating temperature range
- acy55Error code±0.25% of full scale at 25°C (77°F) ±0.5% of full scale over specified operating temperature range
- acy58Error code±0.25% of full scale at 25°C (77°F) ± 0.5% of full scale over specified operating temperature range
- acy77Error code±0.25% of full scale at25°C (77°F) ±0.5% of full scale over specified operating temperature range
- acy78Error code±0.25% of full scale at25°C (77°F); ±0.5% of full scale over specified operating temperature range
- acy79Error code±0.1% of full scale at 25°C (77°F), typical ±0.25% of full scale at 25°C (77°F), maximum ±0.5% of full scale over operating temperature range (maximum)
- acy81Error code±0.25% of full scale at 25°C (77°F), typical ±0.5% of full scale at 25°C (77°F), maximum ±1.0% of full scale over operating temperature range (maximum)
- acy83Error code±0.25% of full scale at25°C (77°F); ±0.5% of full scale over specified operating temperature range
- at0-20Error code±0.25% of full scale at25°C (77°F); ±0.5% of full scale over specified operating temperature range
- at4-20Error code±0.25% of full scale at25°C (77°F); ±0.5% of full scale over specified operating temperature range
- IC694AError codeAnalog Input, Voltage, 4-Channel
- IC695AError codeAnalog Input Module, 6-Channel Isolated Current/Voltage
- IC695CError codeSerial Communications Module, 2 Ports
- IC695EError codeIEC 61850 Ethernet Communication Module
- IC695GError codeYes
- IC695LError codeCan cause communications issues with remote racks if hot-swapped
- IC695PError codePressure Transducer Module
- ime23Error codeFor modules MDL654 and MDL655, the maximum number of inputs per group that can be on at the same time depends on the ambient temperature as displayed in Figure 167. There is no thermal derating for module MDL658
- IN8Error codeAn error condition has been detected by Module. The error code is reported in the first %AI word. If the error was caused by a bad data command, the data has been ignored. Once acknowledged by the program, the %Q command (Clear error) must be toggled to clear the error status
- log16Error codeInput Analog 16 Single-Ended/8 Differential Voltage
- ors99Error codePNC001-Ax: One micro USB for communication with a computer using Command Line Interface. PNC001-Bxxx: One RJ45. Disabled
- ove40Error codeDe-rate total Output 1-4 current to 2.0 A at 60° C
- S1Error codeRed: Terminal block not present or field power error. Field power errors include detecting 125 Vdc when configured for 24 Vdc or detecting only 24 Vdc when configured for 125 Vdc
- S2Error codeGroupx Outputs have ESCP fault
- uts86Error codeVoltage Inputs86
- uts87Error codeVoltage Inputs87