MTU gemi jeneratörü All models error codes
Codes
- 1Error code1. PRE HI ENGINE TEMP. Engine continues to operate
- 2Error code2. HI ENGINE TEMP LED. Engine shuts down
- 3Error code3. PRE LOW OIL PRESSURE. Engine continues to operate
- 4Error code4. LOW OIL PRESSURE. Engine shuts down. NOTE: Also see Step 5
- 5Error code5. OVERCRANK. Engine stops cranking. Or Engine runs, shuts down, and LOW OIL PRESSURE
- 9Error code27. Battery of proper size and voltage
- 10Error code10. LOW ENGINE TEMPERATURE.
- 11Error code11. Engine starts from generator control panel, but will not start automatically or from a remote panel. Automatic or remote starting
- 12Error code12. Engine will not crank
- 13Error code13.
- 16Error code16. ATS will not transfer to Emergency
- 17Error code17. ATS will not transfer to Normal
- 2013-09Error codeAdded tap switch information to Voltage Selector Tap Switch (Optional) section
- 2013-12Error codeAdded arc flash safety information to Hazardous Voltage/External Energy section
- 2016-04Error code
- 2017-08Error codeUpdated Gaseous Fuel System section for current gas product. Updated Electrical Requirements with new generator wiring configuration diagrams. Tap switch content was removed per internal approvals as it is no longer offered. Removed Diesel Fuel Recommendations as it has been superseded by engine-specific documentation
- A1Error codeShort circuit in injector wiring of cylinder A1 or injector defective
- A2Error codeShort circuit in injector wiring of cylinder A2 or injector defective
- A3Error codeShort circuit in injector wiring of cylinder A3 or injector defective
- A4Error codeShort circuit in injector wiring of cylinder A4 or injector defective
- A5Error codeShort circuit in injector wiring of cylinder A5 or injector defective
- A6Error codeShort circuit in injector wiring of cylinder A6 or injector defective
- B1Error codeCamshaft speed sensor (B1) supplies incorrect signal or no signal
- B4Error codeExhaust temperature sensor (B4) in the exhaust pipe supplies incorrect signal or no signal
- B5Error codeThe lube oil pressure at sensor B5.1 has fallen below limit value 1. The lube oil pressure is too low
- B6Error codeThe coolant temperature at sensor B6.1 has exceeded limit value 1. Coolant temperature is too high
- B7Error codeThe lube oil temperature at sensor B7 has exceeded limit value 1. Lube oil temperature is too high
- B9Error codeThe charge-air temperature at sensor B9 has exceeded limit value 1. Charge-air temperature too high
- B10Error codeCharge-air pressure sensor (B10) supplies incorrect signal or no signal
- B13Error codeEmergency stop following a failure of crankshaft speed sensor (B13.1) and camshaft speed sensor (B1)
- B16Error codeThe coolant pressure at sensor B16 has fallen below limit value 1. Coolant pressure is too low
- B34Error codeFuel pressure sensor after main filter (B34.1) supplies incorrect signal or no signal
- B44Error codeThe turbocharger speed at sensor B44 has exceeded limit value 1. The turbocharger speed is too high. Cause: Defect
- B48Error codeThe fuel high pressure at sensor B48.1 has exceeded limit value 1. Fuel pressure is too high
- F33Error codeCoolant level at switch F33 is too low
- F46Error codeSwitch F46 in the collection tank has tripped. A leak has occurred in the HP fuel system
- M8Error codeThe control block M8 of the HP fuel pump cannot be activated
- QL1Error codeEngine operation
- QL3Error codeComponent maintenance
- QL4Error codeExtended component maintenance
- W0501Error codeVisually inspect engine for leaks and general condition
- W1178Error codeReplace pressure pipe neck in cylinder head
- W1505Error codeReplace drive belt of battery-charging generator and water pump