Mazak All models error codes
Codes
- 3-2Error code10 No.900 - No.999, No.1900 - No.1999 (EIA/ISO program error) .............................. 3-94
- AL-100Error codeSpindle Overload
- AL-101Error codeSpindle Temperature High
- AL-102Error codeSpindle Drive Error
- AL-200Error codeServo Alarm on X-Axis
- AL-202Error codeFeedback Signal Error
- AL-600Error codeCNC Software Error
- AL-601Error codeMemory Fault
- BA95Error codeTool nose measurement, sensor width along the X-axis
- BA96Error codeTool nose measurement, sensor width along the Z-axis
- BA97Error codeTool nose measurement, X-coordinate of the sensor’s reference point
- BA98Error codeTool nose measurement, Y-coordinate of the sensor’s reference point
- BA99Error codeTool nose measurement, Z-coordinate of the sensor’s reference point
- E-003Error codeAlarm code E-003 on a Mazak machine generally indicates a servo alarm related to axis positioning errors. You should check the servo motor connections, encoder signals, and ensure that the axis is not obstructed or damaged
- E-015Error codeAlarm code E-015 on a Mazak machine typically indicates a tool breakage or tool load alarm, suggesting that the tool may be damaged or the cutting conditions are causing excessive load
- F33Error codeIncorporation of the MAZATROL tool length into the current position counter valid/invalid
- F114Error codeOutput timing of a tool life alarm
- K46Error codeExcessive pressing error spread (Amount of drooping)
- K48Error codeSpindle FB alarm detection method
- K108Error codePermissible error range for synchronous control
- L1Error codeStylus eccentricity of touch sensor (X-component)
- L2Error codeStylus eccentricity of touch sensor (Y-component)
- L3Error codeRadius of stylus ball of touch sensor (X-component)
- L4Error codeRadius of stylus ball of touch sensor (Y-component)
- L22Error codeData of the tool nose measurement sensor, Sensor width along the X-axis
- L23Error codeData of the tool nose measurement sensor, Sensor width along the Z-axis
- L24Error codeTool nose measurement sensor reference position, X-axis
- L25Error codeTool nose measurement sensor reference position, Z-axis
- LK511Error code
- M130Error codeThe spindle cooling fan is stopped. (Only for 11 kW, 15 kW specification Spindle)
- M169Error codeHigh pressure coolant flows out
- M216Error codeIn the state where the spindle is connected to the C-axis, even if the M212 (C-axis unclamp command) is executed, it is ignored and the current state is maintained
- M355Error codeThe tool replacement command is completed after the turret clamp sensor is turned ON
- M374Error codeIf overload is detected, NC Feed Hold stop is carried out
- M375Error codeIf overload is detected, NC Feed Hold stop and spindle (milling spindle) stop is carried out. This mode is activated after reset
- M376Error codeThe value specified in A*** (OTHER CODE) following M376 is considered as the overload detection level
- M377Error codeThe value specified in A*** (OTHER CODE) following M377 is considered as the overload detection level
- M550Error codeThe discharge pressure of the high pressure coolant is specified as “1”
- M551Error codeThe discharge pressure of the high pressure coolant is specified as “2”
- M552Error codeThe discharge pressure of the high pressure coolant is specified as “3”
- M553Error codeThe discharge pressure of the high pressure coolant is specified as “4”
- M554Error codeThe discharge pressure of the high pressure coolant is specified as “5”
- M555Error codeThe discharge pressure of the high pressure coolant is specified as “6”
- M556Error codeThe discharge pressure of the high pressure coolant is specified as “7”
- M557Error codeSelection of the discharge pressure of the high pressure coolant is disabled
- odu8Error code
- SA138Error codeNumber of gears SA138: Number of spindle gears SA139: Number of motor gears
- TC8Error codeAcceleration pitch error ratio in thread cutting unit
- TC17Error codePitch error correction during threading acceleration