Markasi-Belli-Degil All models error codes
Codes
- S-47Error codeflashing/pulsing Switch
- S2Error codeRight signal icon When this icon is on, it indicates that the right turn signal lamp
- S3Error codeCharging icon When this icon is on, it indicates that the vehicle is in charging
- S4Error codeReady to drive icon When this icon is constantly on, it indicates that the vehicle is
- S5Error codeDriving mode icon When this icon is on, it indicates that the vehicle is in slow
- S6Error codeHigh beam icon When this icon is on, it indicates that the high beam is active.
- S7Error codeParking light icon When this icon is on, it indicates that the parking light is active.
- S8Error codeParking brake status icon When this icon is on, it indicates that the parking brake is
- S9Error codeDoor status icon When this icon is on, it indicates that one of the doors is open.
- S11Error codeLoad dump icon When this icon is on, it indicates that the load shedding
- S11EError code775x790x1035 11 - GN1/1 5x4 mm2
- S12Error codeGlass resistance icon When this icon is on, it indicates that the window resistance is
- S13Error codeFront fog light icon When this icon is on, it indicates that the front fog lamp is
- S14Error codeSeat belt icon When this icon is on, it indicates that the seat belt is not
- S15Error codeRear fog light icon When this icon is on, it indicates that the rear fog lamp is
- S16Error codeRefrigeration stopped. (open DI input)
- S17Error codeDoor open (open DI input)
- S20Error code11020 x 1 20280 x 1 31000 x 1 32100 x 1 32105 x 3
- S20EError code1150x970x1035 20 - GN1/1 5x6mm2
- S25Error codeManual control of outputs
- S29Error codeCase cleaning
- S30Error code11030 x 1 20290 x 1 31000 x 1 32100 x 1 32105 x 3
- S32Error codeDelay of output at start-up
- S40EError code1150x970x1835 40 - GN1/1 5x16 mm2
- S55Error code11066 x 1 20290 x 1 31000 x 1 32100 x 1 32105 x 3
- S75Error code11074 x 1 20310 x 1 31000 x 1 32100 x 1 32105 x 3
- S80Error code11080 x 1 20140 x 1 31010 x 1 32110 x 1 32105 x 3
- S125Error code11125 x 1 20140 x 1 31010 x 1 32110 x 1 32105 x 3
- S160Error code11160 x 1 20200 x 1 31010 x 1 32110 x 1 32105 x 3
- S172Error code11172 x 1 20140 x 1 31010 x 1 32110 x 1 32105 x 3
- S245Error code11248 x 1 20200 x 1 31010 x 1 32110 x 1 32105 x 3
- S440Error code11440 x 1 20360 x 1 31044 x 2 32146 x 1 32168 x 1 31061 x 1 32105 x 3
- S600Error code11600 x 1 20370 x 1 31044 x 2 32146 x 1 32168 x 1 31061 x 1 32105 x 3
- S601Error codeDanger of vessel overfilling Make sure that there is no Bit 9 of
- S603Error codeOperating voltage below speci Check electrical connection Bit 11 of
- SAError codeSDI Address
- SDError codeBanknot boyutunda farklılık Şüpheli banknotu alınız ve "START" düğmesine basarak devam ediniz
- SEError codegarantía final el el
- SE1Error codePlugged fi lter sensor (optional)
- SE2Error codehareket esnasında AÇIK olmalıdır. Eğer hareket sonunda 1 KULLANICI
- SFError codeScaling Factor error - one Check the connections of changer Make corrections to harness or
- SGError codeSection 14 Symbols and Glossary P24x/EN SG/C52
- SH12Error codeGND3 GND2 GND1 GND0 LVDD OUT+ OUT- OUT+
- SIError codeVIQUA y no que productos
- SKError codeToggle incident light / transillumin- 9 Set the illumination intensity
- SLError code4.1.2. Unpacking the machine
- SMError code15to 2160 MHz
- SNError codestring (n = number of characters)
- SN-30Error codeP21.1.11 Sistem Zaman Aşımı 65535
- SOError codethe This is usually the result of excessive wear at the