Markasi-Belli-Degil All models error codes
Codes
- E-002Error codeMain state machine corrupted (software)
- E-03Error code• This probe monitors the Call New Brunswick Service department.
- E-005Error codeSystem reset by watchdog
- E-016Error codeTemperature sensor short
- E-017Error codeSpeed above rotor recognition speed limit
- E-019Error codeRotor code not in rotor table
- E-020Error codeRotor code corrupted
- E-022Error codeSpeed 2 measurement disturbed
- E-027Error codeState of lid latch micro switches implausible
- E-033Error codeHigh pressure in cooling system
- E-036Error codeOver voltage or short circuit at inverter
- E-038Error codeLid latch current abnormal (Speed 0)
- E-040Error codeAcceleration too slow
- E-041Error codeOffset voltage of imbalance sensor implausible
- E-046Error codeLid opened during run
- E-051Error codeSoftware state machine error
- E0-10Error codeC0C 07+30 1.2 Deleted after 1.60
- E001Error codeANA KONTROL baskılı devre kartının EEP-ROM sıfırlama bağlantısı. Gücü KAPALI konuma
- E01Error codeAlarm Test Fail - The connected device has failed Alarm Test. Remove device and allow
- E02Error codeAddressable Set Trouble - The Programmer has detected a trouble condition during address
- E04Error codeLine Mains Power supply too low on Check mains voltage
- E05Error codeLine Mains Power supply too high on Check mains voltage
- E007Error codeMotor too hot 1- Tool is locked because the maximum motor temper
- E008Error codeTool angle fault 1- Problem detected with the tool angle sensor.
- E009Error codeTool invalid parameters 1- Check the tool compatiblity.
- E011Error codeIf electric engine plug is well contacted
- E012Error codeTool EEPROM error 1- The tool memory cannot be read or is invalid.
- E013Error codefailure broken
- E014Error codeif sewing machine handwheel correctly installed.
- E015Error codeModel type error Check operating box
- E018Error codeTorque out of range ! 1- The target torque value is above the tool maximum
- E021Error codeCharacter string Partial
- E023Error codeBaskı ayağını kaldırma motorunun çalışmasında kısa süreli Sıfırlama düğmesine Standart ekran
- E024Error codeDikiş çeşidi veri büyüklüğü çok fazla bastıktan sonra yeniden Standart ekran
- E025Error codeÜst iplik kesici motorunun çalışmasında kısa süreli sapma bastıktan sonra yeniden Standart ekran
- E026Error codeMasura iplik kesici motorunda kısa süreli sapma saptanması bastıktan sonra yeniden Standart ekran
- E029Error codeThe battery is empty. 1- The battery back is discharged. The tool cannot
- E030Error codeİğne mili üst konum hatası bastıktan sonra yeniden Standart ekran
- E031Error codeBattery error 1- Abnormal battery voltage. The tool cannot tighten.
- E032Error codeTool display error 1- Board display malfunction.
- E034Error codeTool memory error 1- The tool memory does not work properly.
- E035Error codeTool memory locked 1- The tool memory is locked to protect old data from
- E037Error codeTool trigger error 1- The tool trigger does not work properly.
- E042Error codeParafudrun Bakımı / Onarımı Parafudr hasar görmüş. Lütfen Müşteri Hizmetleri ile iletişime geçiniz
- E044Error codeAC Güç Kaybı
- E045Error code
- E047Error codeBattery is too low. 1- Check the battery pack.
- E048Error codeBattery type not allowed 1- Battery type not allowed.
- E050Error codeDurdurma düğmesi bastıktan sonra yeniden Adım ekranı
- E052Error codeİplik kopma algılama hatası bastıktan sonra yeniden Adım ekranı