JCB Fastrac traktör All models error codes
Codes
- K4156Error codeECU temperature sensor voltage below normal
- K4157Error codeECU over temperature HIGH ALARM
- K4170Error codeECU Internal fault 0100 - ECU internal power off ERROR at previous afterrun
- K4175Error codeDEF tank level sensor voltage above normal or open circuit
- K4176Error codeDEF tank level sensor voltage below normal
- K4200Error codeDEF tank temperature sensor voltage above normal or open circuit
- K4201Error codeDEF tank temperature sensor voltage below normal
- P0047Error codeDECU Internal Temperature Sensor low
- P0048Error codeDECU Internal Temperature Sensor under range
- P0049Error codeDECU Internal Temperature Sensor high
- P0050Error codeDECU Internal Temperature Sensor over range
- P0051Error codeHand Throttle 5 volt Sensor Supply low
- P0052Error codeHand Throttle 5 volt Sensor Supply under range
- P0053Error codeHand Throttle 5 volt Sensor Supply high
- P0054Error codeHand Throttle 5 volt Sensor Supply over range
- P0059Error codeDECU detected Ignition Supply Voltage is Low
- P0060Error codeDECU detected Ignition Supply Voltage is Low
- P0061Error codeDECU detected Ignition Supply Voltage is High
- P0062Error codeDECU detected Ignition Supply Voltage is High
- P0070Error codeDECU lost CanBus communication with Work Lights
- P0075Error codeDECU Ignition Voltage Low
- P0080Error codeGPS Steering Hydraulic Pressure Low Error
- P0081Error codeGPS Steering Hydraulic Pressure Sensor Open Circuit Error
- P0082Error codeGPS Steering Hydraulic Pressure High Error
- P0083Error codeGPS Steering Hydraulic Over Pressure Error
- P0084Error codeGPS Steering ESV solenoid High Side Driver supply error
- T1427Error codeTECU detected DECU communication had not been received in 2 seconds
- T1450Error codeTransmission fault detected ñ for DECU information
- T1451Error codeTransmission fault detected ñ for DECU information
- T1452Error codeTransmission ECU Software fault (Invalid gear request)
- T1457Error codeOutput shaft speed sensors have speed difference greater than 10%
- T1458Error codeSensed vehicle direction implausible vs current gear
- T1500Error codeTransmission Range Calibration Fault: Clutch Pedal Down value too low
- T1501Error codeTransmission Range Calibration Fault: Clutch Pedal Down value too high
- T1502Error codeTransmission Range Calibration Fault: Clutch Pedal Up value too low
- T1503Error codeTransmission Range Calibration Fault: Clutch Pedal Up value too high
- T1510Error codeTransmission Range Calibration Fault: Rail 1 (point 1) too low
- T1511Error codeTransmission Range Calibration Fault: Rail 1 (point 1) too high
- T1512Error codeTransmission Range Calibration Fault: Rail 1 (point 2) too low
- T1513Error codeTransmission Range Calibration Fault: Rail 1 (point 2) too high
- T1520Error codeTransmission Range Calibration Fault: Rail 2 (point 1) too low
- T1521Error codeTransmission Range Calibration Fault: Rail 2 (point 1) too high
- T1522Error codeTransmission Range Calibration Fault: Rail 2 (point 2) too low
- T1523Error codeTransmission Range Calibration Fault: Rail 2 (point 2) too high
- T1530Error codeTransmission Clutch Calibration Fault: Master Clutch bite point current too low
- T1531Error codeTransmission Clutch Calibration Fault: Master Clutch bite point current too high
- T1532Error codeTransmission Clutch Calibration Fault: Master Clutch time too low
- T1533Error codeTransmission Clutch Calibration Fault: Master Clutch time too high
- T1534Error codeTransmission Calibration Fault: Powershift Valve A bite point too low
- T1535Error codeTransmission Calibration Fault: Powershift Valve A bite point too high