Inverter All models error codes
Codes
- 01Error codeHata 01
- 1-7Error codeProduct Features and Applications Product Features Pure sine wave or modified sine wave Soft start PWM(Pulse Width Modulation) Microprocessor based design With power ON/OFF switch and LED indicator Overload protection / Over voltage protection / Short Circuit protection / Over temperature protection / Reverse polarity protection (by fuses) Product Applications Power tools series：Electric Saw、Drilling Machine、Grinder、Sand bl ast M achine、 Punching Marchine、Weeding Machine、Air Compressor etc. Office series： Computer, Printer、LCD Monitor、Scanning Machine etc. Household Appliance series： Dust Collector、 Fan、 Lamp or LED、Sewing Marchine etc. Kitchen Appliance series： Microwave Oven、 Fridge、 Freezer、 Coffemaker、 -4-
- 02Error codeHata 02
- 03Error codeHata 03
- 9-4Error code1. Indoor Fan Motor
- 10-4Error code1. Indoor Fan Motor
- 10-6Error code2. Making a Diagnosis of the Panel Motor
- 101-103Error code
- 202-203Error code
- 301Error code
- 601Error code
- 1001Error code
- 3301-330Error code
- 3304Error code
- 3401-340Error code
- 3501Error code
- 3601Error code
- 3701Error code
- 3801-380Error code
- 7201-720Error code
- 7508Error code
- A12VError codeGuidelines 3-3-2. If the power more than 1800W, please use tools to tight up the screw. 3-3-3. CAUTION: Before using the inverter,please provide a ground connection wire. Please choose heavy duty, insulated green/yellow wire. Drive into the ground to a depth of 1-2m or more. Batteryˋs C harge We advise that please use deep cycle battery. If you hear the low voltage alarm, please stop the inverter immediately. When the battery is fully charged, the inverter can be used again. If you use the inverter in a car, then it would be necessary to run the engine of your car after each time you use the inverter. You can run the engine for 10 minutes or so to recharge the battery. -8-
- ata01Error codeHata 01
- ata02Error codeHata 02
- ata03Error codeHata 03
- by90Error codeBe sure to completely insert the hex wrench before attempting to turn the valve
- DC5VError codeThe Sketch of Inverter Modified sine wave800W-2000W,Pure sine wave800W-2000W Light Indicators Power (Green) and Fault (Red) Battery Connection Battery Connection AC Outlets Red+ Black- ON/OFF USB DC 5V Switch Fan Ground Connection nut Battery connecting cables -12-
- E0Error codeOutdoor EEPROM malfunction
- E1Error codeIndoor / outdoor units communication error
- E2Error code
- E3Error code
- E4Error code
- E5Error codeVoltage protection of compressor
- E7Error codeIndoor EEPROM malfunction
- for15Error codeTrouble Shooting The measured output courrent of the inverter is too low CAUSES SOLUTION Measure“modified sine wave The range of reading of ”with a“ real effective value common ammeter is too small multimeter” to get the accurate data Charge the battery or Too low current of the inverter change battery -18-
- ft3Error codeFan Speeds Indoor / Outdoor
- FV50SError codeSafety Device CT (Peak current cut-off control) Compressor Discharge Temp. Control Operation cut-off control in abnormal ambient Temp. Overload Relay Model Operation Temp
- FV68SError codeSafety Device CT (Peak current cut-off control) Compressor Discharge Temp. Control Operation cut-off control in abnormal ambient Temp. Overload Relay Model Operation Temp
- is1Error codeAfter repairs, make sure to measure the insulation resistance and confirm that the value is 1 Mohm or more. Any insulation error may cause an electric shock
- m3Error codeAvailable Voltage Range V
- m30Error codeRefrigerant Control
- N-12VError codeType
- P0Error codeTop temperature protection of compressor
- P1Error codeHigh pressure protection(Only for 36K~52K)
- P2Error codeLow pressure protection(Only for 36K,~52K)
- P3Error codeCurrent protection of compressor
- P4Error codeDischarge temperature protection of compressor
- P5Error codeHigh temperature protection of condenser
- P7Error codeHigh temperature protection of evaporator
- R41Error codeIn order to prevent charging e air conditioner that uses R41 diameter at the service valve c has been changed. When rech performing other servicing, us charging hose and manifold g