Hitachi sunucu şasi backplane All models error codes
Codes
- A13Error codeO/OI-L input active range start voltage
- A14Error codeO/OI-L input active range end voltage
- A21Error codeMulti-speed frequency settings (for both motors)
- A39Error codeJog stop mode • 00 Free-run stop, jogging disabled during motor run • 01 Controlled deceleration, jogging disabled during motor run • 02 DC braking to stop, jogging disabled during motor run
- A44Error codeV/f characteristic curve selection • 00 V/f constant torque • 01 V/f variable torque • 02 Sensorless vector control
- A76Error codePV source setting • 00 [OI] terminal (current input) • 01 [O] terminal (voltage input)
- A82Error codeAVR voltage select
- AO1Error code1. Output range: 0 - 10V voltage or 0 - 20mA current 2. Voltage or current output is set by toggle switch 3. Error ± 1%, 25 ° C
- B01Error codeSelection of automatic restart mode • 00 Alarm output after trip, automatic restart disabled • 01 Restart at 0Hz • 02 Resume operation after frequency matching • 03 Resume previous freq. after freq. matching, then decelerate to stop and display trip info
- B02Error codeAllowable under-voltage power failure time
- B03Error codeRetry wait time before motor restart
- B21Error codeOverload restriction operation mode • 00 Disabled • 01 Enabled for accel and constant speed • 02 Enabled for constant speed only
- B22Error codeOverload restriction setting
- B23Error codeDeceleration rate at overload restriction
- B88Error codeRestart mode after FRS • 00 Restart from 0Hz • 01 Restart from frequency detected from actual speed of motor
- B89Error codeData select for digital operator OPE-J • 01 Output frequency (D 01) _ • 02 Output current (D 02) _ • 03 Motor direction (D 03) _ • 04 PID PV feedback (D 04) _ • 05 Input states for input terminals (D 05) _ • 06 Output states for output terminals (D 06) _ • 07 Scaled output frequency (D 07) _
- B92Error codeCooling fan control • 00 Fan always ON • 01 Fan ON during Run, OFF during Stop
- C24Error codeAlarm relay terminal function
- C33Error codeAlarm relay terminal active state
- C41Error codeOverload level setting
- D02Error codeOutput current monitor
- E01Error code• Inverter output was short-circuited • Motor shaft is locked • Load is too heavy • A dual-voltage motor is wired incorrectly Note: The SJ100 will over current trip at nominally 200% of rated current
- E02Error codeOver current event during deceleration
- E03Error codeOver current event during acceleration
- E04Error code• DC braking power(A 54) set too _ high • Current transformer / noise error
- E05Error code• Motor overload is detected by the electronic thermal function
- E07Error code• DC bus voltage exceeds a threshold, due to regenerative energy from motor
- E08Error code• Built-in EEPROM memory experi- enced noise, high temperature, etc
- E09Error code• DC bus voltage decreased enough to cause a control circuit fault
- E10Error code• High electrical noise near inverter • A fault occurred in the built-in CT
- E11Error code• Built-in CPU had internal error
- E13Error code• When (USP) was enabled, an error occurred when power was applied while a Run signal was present
- E14Error code• A ground fault was detected between the inverter output and the motor. This feature protects the inverter, and does not protect humans
- E15Error code• Input voltage was higher than the specified value, 60 sec. after powerup
- E21Error code• Inverter internal temperature is above the threshold
- F202Error codeAcceleration (1) time setting, 2nd motor
- F203Error codeDeceleration (1) time setting, 2nd motor
- H01Error codeAuto-tuning Setting • 00 Auto-tuning OFF • 01 Auto-tune (measure motor resis- tance and inductance, without rotating) • 02 Auto-tune (rotate motor)
- H1Error codeThe STO function is triggered, and the drive stops running. Fault code: 40: Safe torque off (STO)
- H02Error codeMotor data selection • 00 Standard motor data • 01 Auto-tuning data • 02 Adaptive tuning data
- H03Error codeMotor capacity
- H04Error codeMotor poles setting • 2 poles • 4 poles • 6 poles • 8 poles
- H05Error codeMotor speed constant
- H06Error codeMotor stabilization constant
- H20Error codeMotor constant R1
- H21Error codeMotor constant R2
- H22Error codeMotor constant L
- H23Error codeMotor constant I0
- H24Error codeMotor Constant J
- H032Error codeAuto-tuned motor constant L