Hitachi hava perdesi All models error codes
Codes
- Ab110Error codeMulti-speed 0 setting, 1st-motor
- AC120Error codeAcceleration time setting 1, 1st-motor
- AC122Error codeDeceleration time setting 1, 1st-motor
- AF136Error codeInverter rated current ×(0.0 to 2.0)(A)
- AF143Error codeInverter rated current ×(0.0 to 2.0)(A)
- AH-81Error code00(Disable)/ 01(Enable: Error[E120]) 02(Enable:Warning[SSE])
- Ai1Error codeAi2
- Ai2Error codeIt changes the input specification of Analog input 2 (Ai2 terminal). 10V: Voltage input is available. 20mA: Current input is available
- Ao1Error codeIt changes the output specification of Analog output 1 (Ao1 terminal). 10V: Voltage output is applied. 20mA: Current output is applied
- Ao2Error codeIt changes the output specification of Analog output 2 (Ao2 terminal). 10V: Voltage output is applied. 20mA: Current output is applied
- ase200Error codePower supply input wire L1 N +1 + RB Single-phase model V/T2 - Short- circuit Charge lamp Motor output wire bar Power supply input wire S/L2 P/+ RB Three-phase model V/T2 N/- Short- circuit Motor output wire bar Grounding bar: M4×2 Screw size: M3.5, Terminal block width: 7.3 mm
- b001Error code
- b002Error codeInstantaneous power failure/ undervoltage allowed time
- b003Error codeRetry wait time after instantaneous power failure/ undervoltage error
- b004Error codeEnable instantaneous power failure/ undervoltage error while in stop status
- b005Error codeNumber of retries after instantaneous power failure/ undervoltage
- b008Error code
- b011Error codeRetry wait time after overvoltage/ overcurrent error
- b012Error codeElectronic thermal level
- b013Error codeElectronic thermal characteristics selection
- b016Error codeFree electronic thermal current-1 to 3
- b018Error codeFree electronic thermal current-2
- b020Error codeFree electronic thermal current-3
- b021Error codeMonitors output current during acceleration or operation at a constant speed. The current is suppressed by decelerating the motor against any excessive load during acceleration or for sudden load fluctuations at a constant speed
- b022Error codeOverload restriction 1 active level
- b023Error codeOverload restriction 1 action time, 1st- motor
- b024Error codeOverload restriction 2 mode selection
- b025Error codeOverload restriction 2 active level
- b026Error codeOverload restriction 2 action time
- b027Error codeOvercurrent suppression enable
- b028Error codeActive frequency matching restart level
- b033Error codeMotor cable length code selection
- b036Error codeReduced voltage start time
- b050Error codeInstantaneous power failure non-stop function, mode selection
- b051Error codeInstantaneous power failure non-stop function, start voltage level
- b052Error codeInstantaneous power failure non-stop function, target voltage level
- b053Error codeInstantaneous power failure non-stop function, deceleration time
- b054Error codeInstantaneous power failure non-stop function, start frequency decrement
- b075Error codeAmbient temperature
- b089Error codeAutomatic carrier reduction selection
- b092Error codeCooling fan control method selection
- b093Error codeAccumulated cooling fan run time clear
- b094Error codeInitialize target selection
- b098Error codeDetect ground fault selection
- b101Error codeFree-V/f voltage 1
- b103Error codeFree-V/f voltage 2
- b105Error codeFree-V/f voltage 3
- b107Error codeFree-V/f voltage 4
- b109Error codeFree-V/f voltage 5
- b111Error codeFree-V/f voltage 6