Gentherm Blanketrol hasta ısıtma soğutma sistemi All models error codes
Codes
- 704Error codeKoruyucu Gaz Girişi Hava-TCC
- 705Error codeKoruyucu Gaz Girişi Ar-TCC
- 706Error codeSensör Yok P1-TCC
- 707Error codeSensör Yok P2-TCC
- 708Error codeSensör Yok P3-TCC
- 709Error codeSensör Yok P4-TCC
- 710Error codeSensör Yok P5-TCC
- 711Error codeSensör Yok P14-TCC
- 712Error codeSensör yok P6-GCC (sadece VWI veya OptiMix)
- 713Error codeSensör yok P7-GCC (sadece VWI veya OptiMix)
- 714Error codeSensör yok P8-GCC (sadece VWI veya OptiMix)
- 715Error codeSensör yok P9-GCC
- 717Error codeDüşük gerilim-karışım (sadece OptiMix)
- 718Error codeYüksek gerilim-karışım (sadece OptiMix)
- 723Error codeKarışım basıncı kalibrasyonu (sadeceOptiMix)
- 730Error codeSolenoid error V1 (Solenoid hatası V1)
- 733Error codeSolenoid error V4 (Solenoid hatası V4)
- 734Error codeSolenoid error V5 (Solenoid hatası V5)
- 735Error codeSolenoid error V6 (Solenoid hatası V6)
- 736Error codeSolenoid error V7 (Solenoid hatası V7)
- 737Error codeSolenoid error V8 (Solenoid hatası V8)
- 738Error codeSolenoid error V9 (Solenoid hatası V9)
- 739Error codeSolenoid error V10 (Solenoid hatası V10)
- 740Error codeSolenoid error V11 (Solenoid hatası V11)
- 741Error codeSolenoid error V12 (Solenoid hatası V12)
- 752Error codeFaz Hatası-Ch1
- 753Error codeFaz Hatası-Ch2
- 754Error codeFaz Hatası-Ch3
- 756Error codeLeak test results (Sızıntı testi sonuçları)
- 768Error codeGas inlet - O2 Line A (Gaz girişi - Oksijen Hat A)
- 769Error codeGas Inlet - Argon Line B (Gaz Girişi - Argon Hat B)
- 770Error codeGas Inlet - N2 Line B (Gaz Girişi - Azot Hat B)
- 771Error codeGas Inlet - Air Line A (Gaz Girişi - Hava Hat A)
- 789Error codeFieldbus hatası
- 793Error codeAşırı sıcaklık-Con Xfmr
- 794Error codeNo MAC found (Gaz Bağlantı Konsolu bulunamadı)
- EE01Error codeThis message occurs when EE01 appears in the PATIENT temperature display. Both messages appear when the backup processor does not agree with the primary processor. While both messages are displayed, the trouble alarm will sound, and the heater, compressor and pump will turn off. The alarm silence key cannot silence this alarm. Both messages will continue to display, and the trouble alarm will continue to sound until the unit is turned off using the ON/OFF switch or the power cord is disconnected from the power source. If the unit is unplugged before turning the ON/OFF switch, the power fail alarm will activate, and the power fail LED will light. If the unit is turned back on, only “EE01” “REMOVE FROM SERVICE” will reappear in the Status Display and the trouble alarm will sound. The unit cannot be used again until it is serviced. Contact GENTHERM Technical Service
- SPR11Error codeClass A
- to42Error codeENVIROMENTAL CONDITIONS (during storage and transportation) Ambient Temperature (transportation and storage): -40°C - +50°C (-40°F - +122°F) Humidity (transportation and storage): 20% - 95%